5 October 2018 in Physica Status Solidi (a)
26 June 2021 in Physica Status Solidi (RRL) – Rapid Research Letters
Polysilicon recombination junctions whose n‐type bottom layers double as a passivating contact to the silicon surface are investigated. Such recombination junctions are a key element in the interconnection of tandem devices with a silicon bottom cell, and they could be used to simplify the processing sequence of single‐junction cells with interdigitated back contacts (IBCs). Polysilicon tunneling junctions require high processing temperatures to crystallize the layers; however, this also facilitates interdiffusion of dopants, whereas tunnelling relies on degenerate doping concentrations in the constituent layers and sharp interfaces between them. Using secondary‐ion mass spectrometry (SIMS) in dynamic mode, it is found that dopants diffuse readily across the interface, thus compromising the junction. The undesired diffusion is suppressed by modifying the interface with C, O, or a combination of these. Moreover, it is found that the modification does not interfere with diffusion of H, an essential element to passivate defects at the surface of the silicon wafer. Thus, implied open‐circuit voltages (iV oc) of up to 740 mV are demonstrated for contact resistivities less than 40 mΩ cm2.
22 December 2022 in IEEE Journal of Photovoltaics
The recombination of photogenerated charge carriers at metal-semiconductor interfaces remains a major source of efficiency loss in photovoltaic cells. Here, we present SiN x and AlO x nanolayers as promising interface dielectrics to enable high efficiency hole selective passivating contacts. It is demonstrated that SiN x deposited via direct plasma enhanced chemical vapour deposition can be grown controllably at thicknesses of 2 nm. The valence band offsets between crystalline silicon and ultrathin AlO x and SiN x nanolayers are measured as 3.5 and 1.4 eV, respectively. This predicts a larger tunnelling current for holes, compared to SiO x used typically. Resistivity measurements show that SiN x and AlO x nanolayers have lower contact resistivities compared to SiO x , with values as low as 100 mΩ·cm 2 . Analysis of the current transport mechanisms confirmed that tunnelling dominates the conduction through SiN x , while a mixture of tunnelling and pinholes are present in the AlO x structure. Lifetime measurements gave initial indications of the passivation quality of the films, with just 10 cycles of AlO x achieving 260 μ s after annealing and 1.9 ms with extrinsic field effect passivation added. Finally, the intrinsic built-in charge in the dielectrics was determined using surface photovoltage measurements and simulations are used to estimate the influence of nanolayer built-in charge in both poly-Si and dopant-free passivating contacts to enable future high efficiency solar cells.
31 March 2022 in ACS Applied Materials & Interfaces
The integration of passivating contacts based on a highly doped polycrystalline silicon (poly-Si) layer on top of a thin silicon oxide (SiOx) layer has been identified as the next step to further increase the conversion efficiency of current mainstream crystalline silicon (c-Si) solar cells. However, the interrelation between the final properties of poly-Si/SiOx contacts and their fabrication process has not yet been fully unraveled, which is mostly due to the challenge of characterizing thin-film stacks with features in the nanometric range. Here, we apply in situ X-ray reflectometry and diffraction to investigate the multiscale (1 Å–100 nm) structural evolution of poly-Si contacts during annealing up to 900 °C. This allows us to quantify the densification and thinning of the poly-Si layer during annealing as well as to monitor the disruption of the thin SiOx layer at high temperature >800 °C. Moreover, results obtained on a broader range of thermal profiles, including firing with dwell times of a few seconds, emphasize the impact of high thermal budgets on poly-Si contacts’ final properties and thus the importance of ensuring a good control of such high-temperature processes when fabricating c-Si solar cells integrating such passivating contacts. Overall, this study demonstrates the robustness of combining different X-ray elastic scattering techniques (here XRR and GIXRD), which present the unique advantage of being rapid, nondestructive, and applicable on a large sample area, to unravel the multiscale structural evolution of poly-Si contacts in situ during high-temperature processes.
30 August 2024 in ACS Applied Materials & Interfaces
10 August 2018 in AIP Conference Proceedings
Passivating contacts of crystalline silicon (c-Si) solar cells with a poly-silicon layer (poly-Si) on a thin silicon oxide (SiOx) film offer an interesting approach to decrease the recombination current at the metal/c-Si interface and to increase the cell efficiency. This study focuses on the development of boron-doped poly-Si layers deposited by Plasma Enhanced Chemical Vapour Deposition (PECVD) on top of a thin silicon oxide film. First, the deposition and annealing conditions were optimised in order to: (1) reduce the blistering of the poly-Si on the thin SiOx film and (2) improve the poly-Si conductivity. The passivation properties of the resulting structures have been shown to depend on the blister density and have been improved through a hydrogenation step leading to a maximum implied open-circuit voltage value of 721 mV.