26 April 2021 in IEEE Access
This study presents a dual polarized broadband microstrip patch antenna for a 5G mmWave antenna module on an FR4 substrate. The proposed antenna was fabricated using a standard FR4 printed circuit board (PCB) process because of its low cost and ease of mass production. The electrical properties of the FR4 substrate in the 5G mmWave frequency band were also characterized. An air cavity structure was introduced to mitigate the high loss tangent of the FR4 substrate. Capacitive elements such as proximity L-probe feedings and parasitic patches are used to improve the impedance bandwidth of the patch antenna. For the polarization diversity of the massive multiple-input multiple-output (MIMO) capability, the antenna radiator was designed with a symmetrical structure, and the relative position of the L-probes excites the orthogonal resonant modes to enable dual linear polarization. The operation principle of the proposed antenna was thoroughly analyzed by characteristic mode analysis (CMA). The measured bandwidth of a single antenna was 23.1 % (23 ~ 29 GHz) and the gain value was 5 dBi. The measured cross-polarization suppression ratio of single antenna was 15 ~ 20 dB. The measured gain value of 1×4 antenna array was 10 ~ 11 dBi and the cross-polarization suppression ratio was about 20 dB. The size of the proposed single antenna is 0.41λ 0 ×0.41λ 0 ×0.1λ 0 , and that of a 1×4 antenna array is 2.78λ 0 ×0.41λ 0 ×0.1λ 0 . The envelope correlation coefficient (ECC) was calculated and was lower than 0.02 in the 5G mmWave frequency band.
20 October 2020 in IEEE Transactions on Antennas and Propagation
This paper presents an antenna structure with a reconfigurable pattern and polarization for CubeSat applications. The proposed antenna is based on spatial-mapping origami theory and consists of a center-fed 4-way Gysel power divider, delay lines, inside Lamina Emergent Torsion (LET) joints, and four thick planar dipole antennas. The LET joints are used to distribute the mechanical stress of a rigid planar material to form a flexible planar spring structure. The proposed antenna has monopole-like omnidirectional linearly polarized gain patterns in planar mode. Its gain value is about 0.5 dBi at 5.8 GHz. In folded mode, the antenna has about a circularly polarized gain value of about 8.07 dBic and broadside radiation patterns. The measured crosspolarization suppression ratio is about 25 dB, and the axial ratio (AR) value is 1.13 dB at 5.8 GHz. The size of the antenna in planar mode with a cross-shape is 100 × 100 × 0.5 mm3, and its size is in folded mode is 32.5 × 32.5 × 32.5 mm3. The size of the antenna in inactive mode is 35 × 35 × 3 mm3, and its total weight is only 4.73 g.
8 August 2022 in IEEE Antennas and Wireless Propagation Letters
This letter proposes a self-deployable circularly polarized (CP) stacked Yagi–Uda phased antenna array operating at C -band (5.6–6.0 GHz). The proposed antenna system is composed of a 2×2 stacked CP Yagi–Uda antenna array and feeding networks consisting of a reflection-type phase shifter and a four-way Gysel power divider. The proposed phased antenna array is integrated into the top side of a 1U (10 $ \times $ 10 $ \times $ 10 cm 3 ) CubeSat via fully three-dimensional (3-D) printed self-deployable spring hinges and frame. The volume of the proposed antenna is reduced by 69% when folded, and the antenna deploys to the desired shape without any actuators or power. The designed reflection-type phase shifter has 0°–373° analog phase-shifting range and the four-way Gysel power divider feeds each of the 2 $ \times $ 2 antenna array. The proposed self-deployable phased antenna array has 13.5 dBic left-handed circular polarized gain and +/−10° beam steering angle.
28 March 2024 in IEEE Antennas and Wireless Propagation Letters
This paper proposes a novel rhombic dual-polarized and dual-band patch antenna array design for 5G mmWave mobile devices as an antenna-in-package (AiP). The proposed antenna consists of a stacked patch and a parasitic patch that are designed to operate at dual frequencies (28 and 39GHz). An asymmetric stack-up strategy is used to maximize antenna performance within the constraints of the form factor. To address the limitations of elongated asymmetrical structures, the rhombic patch is utilized to achieve dual-polarization capabilities. The RF front-end module (RFFE), which integrates the proposed AiP (1×4 array antenna), is also fabricated and tested for its gain and beam-steering performance. The results show a maximum gain of 10.4 dBi at the lower band (LB) and 11.0 dBi at the higher band (HB) with beam-steering capabilities of ±45 degrees in both bands.
20 May 2022 in IEEE Antennas and Wireless Propagation Letters
This letter presents a foldable vertically stacked Yagi–Uda antenna at millimeter-wave (mmWave) frequency band. The proposed antenna is built on a FR4 substrate. The antenna consists of a balun, feed dipole element, stacked folded dipole, and inside lamina emergent torsional (LET) joint array. The LET joint array is introduced to reduce and distribute the mechanical stress generated in folding the rigid FR4 substrate. In the planar mode, the antenna results in a measured gain value of 4.9 dBi at the design frequency 24 GHz with a cross-polarization suppression level of less than 12 dB. In the folded mode, the antenna has a measured gain value of 3.9 dB at the target frequency 24 GHz with a cross-polarization suppression level of less than 10 dB. Both operation modes of the proposed antenna cover the broad bandwidth from 23 to 28 GHz (about 20 $\%$ ).
11 May 2023 in IEEE Transactions on Electromagnetic Compatibility
This research developed a mmWave electromagnetic (EM) absorber with a simply punched hole pattern, which was introduced on the flat CIP/epoxy composite to overcome the limitation of the magnetic materials. This absorber was designed on a carbonyl iron powder (CIP) and epoxy resin composite with Snoek's limit of about 26 GHz. First, the morphologies of the fabricated CIP/epoxy composite were characterized by scanning electron and atomic force microscopies. Subsequently, the constitutive parameters of the CIP/epoxy composite were measured in the frequency range of 26.5–50 GHz. These measured constitutive parameters of the CIP/epoxy composite material were iteratively revised by the curve-fitting technique to improve the measurement accuracy. An equivalent circuit model was utilized to determine the reflection coefficient of the hole-patterned CIP/epoxy composite mmWave EM absorber, taking into account its material parameters and dimensions. A comprehensive analysis was conducted to evaluate how the performance of the absorber is affected by the dimensions of its unit cell. This was achieved by utilizing both the equivalent circuit and full-wave FEM simulation. The absorption performance of the hole-patterned CIP/epoxy composite mmWave EM absorber is experimentally demonstrated at different angles and polarizations in 26.5–36.5 GHz.