Baisong Chen

Baisong Chen

Auto-generated profile, based on publicly available information

Baisong Chen

State Key Laboratory of Integrated Optoelectronics, College of Electronic Science and Engineering, Jilin University, Changchun, China

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 May 2024 in Photoacoustics
Verified
Journal Article
Open access
LLLixian Liu
Lixian Liu
HHHuiting Huan
Huiting Huan
XZXueshi Zhang
Xueshi Zhang
LZLe Zhang
Le Zhang
JZJinsong Zhan
Jinsong Zhan
AMAndreas Mandelis
Andreas Mandelis
We present a sensitive and compact quantum cascade laser-based photoacoustic greenhouse gas sensor for the detection of CO2, CH4 and CO and discuss its applicability toward on-line real-time trace greenhouse gas analysis. Differential photoacoustic resonators with different dimensions were used and optimized to balance sensitivity with signal saturation. The effects of ambient parameters, gas flow rate, pressure and humidity on the photoacoustic signal and the spectral cross-interference were investigated. Thanks to the combined operation of in-house designed laser control and lock-in amplifier, the gas detection sensitivities achieved were 5.6 ppb for CH4, 0.8 ppb for CO and 17.2 ppb for CO2, signal averaging time 1 s and an excellent dynamic range beyond 6 orders of magnitude. A continuous outdoor five-day test was performed in an observation station in China’s Qinling National Botanical Garden (E longitude 108°29’, N latitude 33°43’) which demonstrated the stability and reliability of the greenhouse gas sensor.

1 July 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
ZWZiming Wang
Ziming Wang
CLChengming Li
Chengming Li
BCBaisong Chen
Baisong Chen
HDHaolun Du
Haolun Du
Junfeng SongJunfeng Song
Junfeng Song
Min TaoMin Tao
Min Tao
Optical phased array (OPA) is a suitable device for producing emission beams in LiDAR. In order to achieve high-speed scanning control of the output beam by OPA chips, we designed and produced a 128-channel silicon-based OPA chip based on electro-optic modulation. Considering the characteristics of multi-phase control in electro-optic OPA chips, a parallel dual-port random access memory (RAM) inside a field programmable gate array (FPGA) technology is used to achieve optical phase control for each channel. The entire system is implemented by existing FPGA chips and digital-to-analog converters (DACs). To implementing the circuit system, we also built a high-speed testing environment for OPA scanning. The system was used to verify the main performance of our designed OPA chip and achieve high-speed scanning control. The test results show that our designed OPA chip and control circuit can achieve fast scanning of the emission beam. The optical phase configuration time is less than 5 μ s. This system can meet the requirements of fast scanning control for all solid-state LiDAR optical emission modules. This work lays the foundation for our subsequent development of OPA-based all solid-state LiDAR prototype.

11 December 2024 in Sensors
Verified
Journal Article
Open access
PDF file
XYXiu Y ang
Xiu Y ang
BCBaisong Chen
Baisong Chen
YHYuyang He
Yuyang He
CZChenchen Zhu
Chenchen Zhu
XZXing Zhou
Xing Zhou
Xukun YinXukun Yin
Xukun Yin
A highly sensitive sulfur dioxide (SO2) photoacoustic gas sensor was developed for the sulfur hexafluoride (SF6) decomposition detection in electric power systems by using a novel 266 nm low-cost high-power solid-state pulse laser and a high Q-factor differential photoacoustic cell. The ultraviolet (UV) pulse laser is based on a passive Q-switching technology with a high output power of 28 mW. The photoacoustic signal was normalized to the laser power to solve the fluctuation of the photoacoustic signal due to the power instability of the UV laser. A differential photoacoustic cell can obtain a high Q-factor and reduce the gas flow noise in SF6 buffer gas. The parameters of the SO2 sensor system were optimized in terms of laser power and operating pressure. A 1σ detection limit (SNR = 1) of 2.34 ppb was achieved with a 1 s integration time, corresponding to a normalized noise equivalent absorption (NNEA) coefficient of 7.62 × 10−10 cm−1WHz−1/2.

19 June 2025 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
ZGZeyu Gang
Zeyu Gang
YZYunshan Zhang
Yunshan Zhang
QNQuanxin Na
Quanxin Na
SGShijian Guan
Shijian Guan
JLJun Lu
Jun Lu
XCXiangfei Chen
Xiangfei Chen
A low-cost hybrid integrated narrow linewidth laser is proposed in this paper. The monolithically integrated 18- channel distributed feedback (DFB) narrow linewidth laser array with a wavelength interval of 0.8 nm is designed and precisely fabricated using reconstruction equivalent chirp (REC) technique, exhibiting good single-mode performance for each channel, with the typical linewidth less than 200 kHz. One channel of the laser array is integrated with the silicon nitride (Si3N4) external cavity chip through the photonic wire bonding (PWB) technique. Both the linewidth reduction effect of the passive external cavity and the coupling efficiency between chips by the polymer waveguide are numerically calculated. The compactly packaged device can be tuned to seven distinct self-injection-locked states with 0.4 nm spectral spacing, where the maximum linewidth is 10.9 kHz and the minimum linewidth is 9.1 kHz. Meanwhile, the side-mode suppression ratio (SMSR) is higher than 54.3 dB and the output power is 3.6 ± 0.9 dBm for each self-injection-locked state.

18 June 2025 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
WYWenqiang Yue
Wenqiang Yue
YFYunhao Fu
Yunhao Fu
XHXiaolong Hu
Xiaolong Hu
Min TaoMin Tao
Min Tao
PWPeng Wang
Peng Wang
LWLijun Wang
Lijun Wang
In autonomous driving, the fusion of camera and LiDAR data is critical for accurate environmental perception, with high-precision extrinsic calibration playing a pivotal role. Optical phased array (OPA) LiDAR, due to its advantages in solid-state scanning, coherent detection, immunity to mechanical fatigue and external interference, and eye safety, represents a promising direction in next-generation LiDAR technology. Conventional LiDAR-camera calibration approaches generally rely on spatial or reflectivity-based point cloud features to infer shared correspondences, followed by nonlinear optimization. However, three key challenges remain: (1) the absence of publicly available datasets for the emerging OPA LiDAR; (2) inaccuracies from sparse point clouds, foreground inflation, and bleeding points affecting feature correspondence; and (3) reliance on complex calibration targets and computationally intensive processes, reducing robustness and efficiency. To overcome these limitations, we propose, for the first time, four joint calibration methods specifically designed for OPA LiDAR. These methods utilize OPA’s directional scanning to treat each scan point as a reliable 3D feature that can be directly matched to corresponding 2D image features, enabling efficient global nonlinear optimization. Experimental validation demonstrates that our methods achieve higher calibration accuracy and significantly reduced computational time compared to existing state-of-the-art techniques. This offers a robust and efficient solution for future multi-sensor fusion systems centered around OPA LiDAR.

1 January 2009
Verified
Conference Paper
Closed access
ZFZhuo Fu
Zhuo Fu
JWJindi Wang
Jindi Wang
JSJinling Song
Jinling Song
Hongmin ZhouHongmin Zhou
Hongmin Zhou
Huaguo HuangHuaguo Huang
Huaguo Huang
BCBaisong Chen
Baisong Chen
The Effective Plant Area Index (PAIe) of forest canopy is an important parameter in the canopy reflectance modeling and validation. PAIe can be transformed to leaf area index (LAI) with clumping index. But it is still very difficult to obtain its ground truth value by in situ measurement. In this study, we measured PAIe of 3 typical wood land sites in China by means of three indirect optical techniques: plant canopy analyzer LAI-2000, TRAC, and Digital Fisheye Camera. The 5 measured stands include Qinghai spruce, peach, poplar, willow and silver chain. In this paper, the forest canopy PAIe measured by those three instruments is compared firstly. Then our new approach is how to use the three measured data to get the better PAIe estimation with less overall error. The method of minimizing overall error is adopted to produce PAIe of the sample plots in our study sites, which has less overall error comparing with the PAIe measured by each individual instrument. This approach is also validated by using computer simulated wide-angle viewing pictures when true LAI/PAIe values are given.