Robert Macků

Robert Macků

Auto-generated profile, based on publicly available information

Robert Macků

Department of Physics, Faculty of Electrical Engineering and Communication, Brno University of Technology, Czech Republic

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2018 in Mechanical Systems and Signal Processing
Verified
Journal Article
Open access
YBYang Bai
Yang Bai
PTPavel Tofel
Pavel Tofel
Zdenek HadasZdenek Hadas
Zdenek Hadas
JSJan Smilek
Jan Smilek
PLPetr Losak
Petr Losak
RMRobert Macku
Robert Macku

1 February 2022 in Polymers
Verified
Journal Article
Open access
PDF file
TPTatiana Pisarenko
Tatiana Pisarenko
NPNikola Papež
Nikola Papež
Dinara SobolaDinara Sobola
Dinara Sobola
Ștefan ȚăluȘtefan Țălu
Ștefan Țălu
KČKlára Částková
Klára Částková
Jaroslav KastylJaroslav Kastyl
Jaroslav Kastyl
This study is focused on the characterization and investigation of polyvinylidene fluoride (PVDF) nanofibers from the point of view of macro- and nanometer level. The fibers were produced using electrostatic spinning process in air. Two types of fibers were produced since the collector speed (300 rpm and 2000 rpm) differed as the only one processing parameter. Differences in fiber’s properties were studied by scanning electron microscopy (SEM) with cross-sections observation utilizing focused ion beam (FIB). The phase composition was determined by Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy. The crystallinity was determined by differential scanning calorimetry (DSC), and chemical analysis of fiber’s surfaces and bonding states were studied using X-ray photoelectron spectroscopy (XPS). Other methods, such as atomic force microscopy (AFM) and piezoelectric force microscopy (PFM), were employed to describe morphology and piezoelectric response of single fiber, respectively. Moreover, the wetting behavior (hydrophobicity or hydrophilicity) was also studied. It was found that collector speed significantly affects fibers alignment and wettability (directionally ordered fibers produced at 2000 rpm almost super-hydrophobic in comparison with disordered fibers spun at 300 rpm with hydrophilic behavior) as properties at macrolevel. However, it was confirmed that these differences at the macrolevel are closely connected and originate from nanolevel attributes. The study of single individual fibers revealed some protrusions on the fiber’s surface, and fibers spun at 300 rpm had a core-shell design, while fibers spun at 2000 rpm were hollow.

30 May 2010 in Advances in Optical Technologies
Verified
Journal Article
Open access
PDF file
PTP. Tománek
P. Tománek
PŠP. Škarvada
P. Škarvada
RMR. Macků
R. Macků
LGL. Grmela
L. Grmela
Near-surface defects in solar cell wafer have undesirable influence upon device properties, as its efficiency and lifetime. When reverse-bias voltage is applied to the wafer, a magnitude of electric signals from defects can be measured electronically, but the localization of defects is difficult using classical optical far-field methods. Therefore, the paper introduces a novel combination of electric and optical methods showing promise of being useful in detection and localization of defects with resolution of 250 nm using near-field nondestructive characterization techniques. The results of mapped topography, local surface reflection, and local light to electric energy conversion measurement in areas with small defects strongly support the development and further evaluation of the technique.

15 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
PČPetr Černohorský
Petr Černohorský
TPTatiana Pisarenko
Tatiana Pisarenko
NPNikola Papež
Nikola Papež
Dinara SobolaDinara Sobola
Dinara Sobola
Ștefan ȚăluȘtefan Țălu
Ștefan Țălu
PSPetr Sedlák
Petr Sedlák
The paper specifies the electrostatic spinning process of specific polymeric materials, such as polyvinylidene fluoride (PVDF), polyamide-6 (PA6, Nylon-6) and their combination PVDF/PA6. By combining nanofibers from two different materials during the spinning process, new structures with different mechanical, chemical, and physical properties can be created. The materials and their combinations were subjected to several measurements: scanning electron microscopy (SEM) to capture topography; contact angle of the liquid wettability on the sample surface to observe hydrophobicity and hydrophilicity; crystallization events were determined by differential scanning calorimetry (DSC); X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and Fourier-transform infrared spectroscopy (FT-IR) to describe properties and their changes at the chemical level. Furthermore, for the electrical properties of the sample, the dielectric characteristics and the piezoelectric coefficient were measured. The advantage of the addition of co-polymers was to control the properties of PVDF samples and understand the reasons for the changed functionality. The innovation point of this work is the complex analysis of PVDF modification caused by mixing with nylon PA6. Here we emphasize that the application of nylon during the spin influences the properties and structure (polarization, crystallization) of PVDF.

1 September 2014 in Applied Surface Science
Verified
Journal Article
Closed access
PŠPavel Škarvada
Pavel Škarvada
PTPavel Tománek
Pavel Tománek
PKPavel Koktavý
Pavel Koktavý
RMRobert Macků
Robert Macků
JŠJiří Šicner
Jiří Šicner
LGLubomír Grmela
Lubomír Grmela

8 June 2010 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
RMRobert Macku
Robert Macku
PKPavel Koktavy
Pavel Koktavy