8 May 2020 in Science Advances
Soft machines typically exhibit slow locomotion speed and low manipulation strength because of intrinsic limitations of soft materials. Here, we present a generic design principle that harnesses mechanical instability for a variety of spine-inspired fast and strong soft machines. Unlike most current soft robots that are designed as inherently and unimodally stable, our design leverages tunable snap-through bistability to fully explore the ability of soft robots to rapidly store and release energy within tens of milliseconds. We demonstrate this generic design principle with three high-performance soft machines: High-speed cheetah-like galloping crawlers with locomotion speeds of 2.68 body length/s, high-speed underwater swimmers (0.78 body length/s), and tunable low-to-high-force soft grippers with over 1 to 103 stiffness modulation (maximum load capacity is 11.4 kg). Our study establishes a new generic design paradigm of next-generation high-performance soft robots that are applicable for multifunctionality, different actuation methods, and materials at multiscales.
1 June 2013 in IEEE Transactions on Robotics
The ability to jump is found widely among small animals such as frogs, grasshoppers, and fleas. They jump to overcome large obstacles relative to their small sizes. Inspired by the animals' jumping capability, a miniature jumping robot-Michigan State University (MSU) Jumper-has been developed. In this paper, the mechanical design, fabrication, and experimentation of the MSU jumper are presented. The robot can achieve the following three performances simultaneously, which distinguish it from the other existing jumping robots. First, it can perform continuous steerable jumping that is based on the self-righting and the steering capabilities. Second, the robot only requires a single actuator to perform all the functions. Third, the robot has a light weight (23.5 g) to reduce the damage that results from the impact of landing. Experimental results show that, with a 75° take-off angle, the robot can jump up to 87 cm in vertical height and 90 cm in horizontal distance. The robot has a wide range of applications such as sensor/communication networks, search and rescue, surveillance, and environmental monitoring.
27 September 2023 in Nature Communications
Shape-morphing robots can change their morphology to fulfill different tasks in varying environments, but existing shape-morphing capability is not embedded in a robot’s body, requiring bulky supporting equipment. Here, we report an embedded shape-morphing scheme with the shape actuation, sensing, and locking, all embedded in a robot’s body. We showcase this embedded scheme using three morphing robotic systems: 1) self-sensing shape-morphing grippers that can adapt to objects for adaptive grasping; 2) a quadrupedal robot that can morph its body shape for different terrestrial locomotion modes (walk, crawl, or horizontal climb); 3) an untethered robot that can morph its limbs’ shape for amphibious locomotion. We also create a library of embedded morphing modules to demonstrate the versatile programmable shapes (e.g., torsion, 3D bending, surface morphing, etc.). Our embedded morphing scheme offers a promising avenue for robots to reconfigure their morphology in an embedded manner that can adapt to different environments on demand.
1 April 2021 in Soft Robotics
Various actuators (e.g., pneumatics, cables, dielectric elastomers, etc.) have been utilized to actuate soft robots. Besides widely used actuators, a relatively new artificial muscle—twisted-and-coiled actuators (TCAs)—is promising for actuating centimeter-scale soft robots because they are low cost, have a large work density, and can be driven by electricity. However, existing works on TCA-actuated soft robots in general can only generate simple bending motion. The reason is that TCAs fabricated with conventional methods have to be preloaded to generate a large contraction, and thus cannot actuate soft robots properly. In this work, an upgraded technique is presented to fabricate TCAs that can deliver 48% free strokes (contraction without preloading). We first compare the static performance of TCAs with free strokes with conventional TCAs, and then characterize how will the fabrication parameters influence the TCAs' stroke and force capability. After that, we demonstrate that such TCAs can actuate centimeter-scale soft robots with programmable motions (gripping, twisting, and three-dimensional bending). Finally, we combine those motions to demonstrate a soft robotic arm that can perform a pick-and-place task. We expect that TCAs with free strokes can enable miniature soft robots with rich three-dimensional motions for both locomotion and manipulation. Because TCAs are electrically driven, we can also potentially develop untethered soft robots by carrying onboard batteries and control circuits.
8 April 2015 in IEEE/ASME Transactions on Mechatronics
Inspired by the aerial maneuvering ability of lizards, we present the design and control of MSU (Michigan State University) tailbot - a miniature-tailed jumping robot. The robot can not only wheel on the ground, but also jump up to overcome obstacles. Moreover, once leaping into the air, it can control its body angle using an active tail to dynamically maneuver in midair for safe landings. We derive the midair dynamics equation and design controllers, such as a sliding mode controller, to stabilize the body at desired angles. To the best of our knowledge, this is the first miniature (maximum size 7.5 cm) and lightweight (26.5 g) robot that can wheel on the ground, jump to overcome obstacles, and maneuver in midair. Furthermore, tailbot is equipped with on-board energy, sensing, control, and wireless communication capabilities, enabling tetherless or autonomous operations. The robot in this paper exemplifies the integration of mechanical design, embedded system, and advanced control methods that will inspire the next-generation agile robots mimicking their biological counterparts. Moreover, it can serve as mobile sensor platforms for wireless sensor networks with many field applications.
24 May 2018 in IEEE Transactions on Industrial Electronics
In order to deal with automatic assembly problems for flexible components, we develop contact states analysis, jamming analysis and force control strategies for flexible dual peg-in-hole assembly. Firstly, the contact states in large and small deformation stages are enumerated respectively. Secondly, the relationship between forces and moments is derived, and the jamming states for different stages are analyzed. Thirdly, the control strategies are also presented. Finally, the results of experiments verified the effectiveness of the contact state analysis, jamming analysis and force control strategies.