26 February 2014 in Materials Science Forum
The aim of this study consists in comparing the effects of temperature on various SiC power devices. Electrical characteristics have been measured for temperatures from 100K to 525K. All devices are suitable for high temperature. However, SiC MOSFETs are not a good choice for cryogenic temperature, while SiC BJTs are less affected by temperature than other components, especially for cryogenic temperature.
14 May 2012 in Materials Science Forum
Selective epitaxial growth in buried patterns was studied using the vapour-liquid-solid mechanism in Al-Si melt in order to obtain p+-doped SiC localized layers on 4H-SiC substrate. Homogeneous deposition with step bunched morphology was obtained by adding propane at room temperature before growth at 1100°C. Patterns as large as 800 µm and as narrow as 10 µm were completely filled in this way. The deposition kinetics demonstrates that the process is self limited and mainly depends on the initial amount of Si in the liquid. The deposit is highly p-type doped and the p-n junction is demonstrated.
22 August 2011 in Advanced Materials Research
Progress in semiconductor technologies have been so consequent these last years that theoretical limits of silicon, speci cally in the eld of high power, high voltage and high temperature have been achieved. At the same time, research on other semiconductors, and es- pecially wide bandgap semiconductors have allowed to fabricate various power devices reliable and performant enough to design high e ciency level converters in order to match applications requirements. Among these wide bandgap materials, SiC is the most advanced from a techno- logical point of view: Schottky diodes are already commercially available since 2001, JFET and MOSFET will be versy soon. SiC-based switches Inverter e ciency bene ts have been quite established. Considering GaN alternative technology, its driving force was mostly blue led for optical drive or lighting. Although the GaN developments mainly focused for the last decade on optoelectronics and radio frequency, their properties were recently explored to design devices suitable for high power and high e ciency applications. As inferred from various studies, due to their superior material properties, diamond and GaN should be even better than SiC, silicon (or SOI) being already closed to its theoretical limits. Even if the diamond maturity is still far away from GaN and SiC, laboratory results are encouraging speci cally for very high voltage devices. Apart from packaging considerations, SiC, GaN and Diamond o ers a great margin of progress. The new power devices o er high voltage and low on-resistance that enable important reduction in energy consumption in nal applications. Applications for wide bandgap materials are the direction of high voltage but also high temperature. As for silicon technology, WBG-ICs are under development to take full bene ts of power and drive integration for high temperature applications.
14 May 2012 in Materials Science Forum
Optical Beam Induced Current (OBIC) measurements have been performed on 4H-SiC avalanche diodes with very thin and highly doped avalanche region. The light source used in this study is an Ar-laser with a wavelength of 351 nm which results in a mixed carrier injection. From these measurements, impact ionization coefficients for 4H-SiC have been extracted in the electric field range from 3 to 4.8 MV/cm. In combination with ionization coefficients in our previous paper extracted from diodes with lowly doped avalanche region, we propose a set of parameters of impact ionization coefficients for 4H-SiC, applicable to a wide electric field range.
14 May 2012 in Materials Science Forum
4H-SiC vertical bipolar power diodes have been fabricated with bilayer metallic anode contact based on an Al-Ti-Ni ohmic contact and a thick Al over-metallization. An optical window of 100 × 100 μm2 has been created through the anode contact with a SIMS Cameca IMS 4F equipment using Cs+ primary ions at 10 kV and with a beam spot size of 100 nm. The current/voltage characteristics of the diodes show that the SIMS process does not induce an increase of the leakage currents in forward nor in reverse bias. OBIC UV photogeneration occurs under the optical window and not under the contact metal.
15 October 2006 in Materials Science Forum
The potential of SiC MESFETs has been demonstrated for high frequency applications on several circuits in the 1-5 GHz frequency range. Although MESFET structures are conventionally used for RF applications, in this paper we report a low voltage (180V) power switch and its current limiting application based on a double gate MESFET structure, showing enhanced forward and blocking capabilities. The reported devices utilize a thin highly doped p-type layer implanted at high energy as buffer layer. Various layouts have been fabricated, varying the gate length; with either a single gate (p-buried layer connected to source) or double gate (one Schottky, and the second on the P-buried layer). Gate RESURF field-plate variation has been also included at the gate electrode. The I(V) electrical characterization validates the double gate configuration benefits. This double gate structure shows a higher gate transconductance than the single gate one. High voltage measurements in conducting mode (180V, 160mA/mm, 30W/mm) confirm the operation of the MESFET as a current limiting device, with excellent gate control capabilities at temperature up to 190°C.