Metal oxide semiconductor has attracted so much attention due to its high carrier mobility. Herein, thermoelectric study of nanocrystalline SnO2 through a simple co-precipitation method is conducted to enhance the Seebeck coefficient (S). X-ray diffraction, thermogravimetric analysis (TGA), resistivity (r), Seebeck coefficient (S), and power factor (PF) measurements are conducted to analyze the thermoelectric properties of the material. The measurements show that there are two interesting results, which are the unusual resistivity behavior and the high value of the S. Resistivity behavior shows a non-reflective intermediate semiconductor-metals behavior where the turning point occurs at 250 o C. This behavior is strongly correlated to the surface oxide reaction due to annealing temperature. The maximum S likely occurs at 250 ºC, since the curve shows a slight thermopower peak at 250 ºC. The value of the S is quite high with around twenty times higher than other publications about SnO2 thermoelectric material, this happens due to the bandgap broadening. The energy gap of SnO2 calculated using density functional theory (DFT), which was performed by Quantum Espresso 6.6. The result shows that there is a broadening energy gap at different momentum or wave factor. Nanocrystalline semiconductors material is giving an impact to increase the width of bandgap due to quantum confinement and could enhance the thermopower especially in SnO2 nanocrystalline
This study describes a method by which to synthesize SiO2-based graphene nanoballs (SGB) using atmospheric pressure chemical vapor deposition (APCVD) with copper vapor assistance. This method should solve the contamination, damage, and high costs associated with silica-based indirect graphene synthesis. The SGB was synthesized using APCVD, which was optimized using the Taguchi method. Multiple synthesis factors were optimized and investigated to find the ideal synthesis condition to grow SGB for thermoelectric (TE) applications. Raman spectra and FESEM-EDX reveal that the graphene formed on the silicon nanoparticles (SNP) is free from copper. The prepared SGB has excellent electrical conductivity (75.0 S/cm), which shows better results than the previous report. Furthermore, the SGB nanofillers in bismuth telluride (Bi2Te3) nanocomposites as TE materials exhibit a significant increment in Seebeck coefficients (S) compared to the pure Bi2Te3 sample from 109 to 170 μV/K at 400 K, as well as electrical resistivity decrement. This approach would offer a simple strategy to improve the TE performance of commercially available TE materials, which is critical for large-scale industrial applications.
In this study, fabrication of Pr15-xDyxFe77B8 (at.%) alloys with x = 0, 1, 2, and 3 compositions was performed with a mini vacuum arc melting furnace. The alloys were successively annealed in an inert atmosphere for microstructure homogenization. All alloys exhibit the typical characteristics of a permanent magnet. The coercivity gradually increases with increasing atomic fraction of Dy. The heat treatment applied to the samples changed the properties from those of a permanent magnet to those of a microwave absorber. The reflection loss (RL) value evaluated by a Vector Network Analyzer (VNA) shows broadband absorption characteristics in the full 8 GHz–12 GHz frequency range. The RL and bandwidth increase with the addition of the Dy substitute. The as-cast and annealed Pr15- xDyxFe77B8 alloy with the x = 1 composition shows superior absorption, starting from the 8 GHz frequency and increasing progressively, reaching less than -17 dB or an absorption of more than 85.0 % at a peak frequency of 10.5 GHz, after which it weakens to -6 dB at a frequency close to 12 GHz. Heat-treated samples were characterized by absorption with two almost overlapping absorption peaks at frequencies of 9.5 GHz and 11.5 GHz, leading to very broadband absorption across the full frequency range (8–12 GHz). It is concluded that permanent magnetic materials could be converted into radar absorbing materials (RAM). RAM based on heat-treated rare earth permanent magnet has broadband absorption characteristics.
8 January 2026 in Journal of Applied Polymer Science
The intricate competition between seed formation and the growth-limited area in 2D transition metal dichalcogenides has long hindered their potential applications. This study investigated the morphological and photophysical characteristics of few-layer tungsten disulfide (FL-WS2) thin films deposited on SiO2/Si substrates via pulsed laser deposition (PLD). To induce morphological changes, the number of laser pulses was varied (50, 150, and 300 shots), followed by a post-deposition annealing treatment. Atomic force microscopy (AFM) demonstrated three distinct morphological features: continuous films, particulates, and islands, indicative of a growth evolution consistent with the Stranski–Krastanov (layer-plus-island) mechanism. X-ray photoelectron spectroscopy (XPS) revealed the presence of a semiconducting phase of 2H-WS2 and sulphur-deficient species (WSx) in the films. While Raman modes characteristic of WS2 were observed, the absence of photoluminescence (PL) emission suggested the presence of defect states in the as-grown thin films. Upon post-annealing treatment, we observed a reduction in WSx species (150 and 300 laser shots) accompanied by a reduction of particulate density. This, in turn, triggers a defect state suppression, by which the PL spectra of all samples emerge, unveiling the near-resonance emission and excitonic features. This observation was confirmed by the density functional theory (DFT) simulation, pointing to the presence of an extra energy level around the K point of the Brillouin zone at high concentration of sulphur vacancy, which corresponds to the splitting of near-resonant PL emission. In addition, two pronounced Raman modes at 264 cm−1 and 334 cm−1 are associated with structural relaxation due to post-annealing. This relationship between morphological characteristics and emissive behaviour of large-area FL-WS2 thin films provides valuable insights into their photophysical modulation, paving the way for advanced photonic applications.