Oleg Dekusha

Oleg Dekusha

Auto-generated profile, based on publicly available information

Oleg Dekusha

General Energy Institute of NAS of Ukraine

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

30 December 2022 in Energies
Verified
Journal Article
Open access
PDF file
OHOleksandra Hotra
Oleksandra Hotra
Svitlana KovtunSvitlana Kovtun
Svitlana Kovtun
ODOleg Dekusha
Oleg Dekusha
ŻGŻaklin Grądz
Żaklin Grądz
VBVitalii Babak
Vitalii Babak
JMJoanna Maria
Joanna Maria
When evaluating the energy efficiency of buildings and implementing the necessary measures to increase energy efficiency levels, thermal technical characteristics are determined. For this purpose, in situ measurements of the thermal resistance of external enclosing structures were carried out. One of the methods most often used by researchers is the non-destructive method—the heat flow meter (HFM) method regulated by ISO 9869. In the case of surveying a building with a high level of thermal resistance, researchers are faced with low-density heat flux measurements, which is always a difficult task due to significant fluctuations and the influence of external factors on the measurement results. This is due to the fact that it is difficult to determine what is a useful signal and what is a consequence of the effects of non-stationarity and heat transfer conditions. The article provides an example of low-density heat flux measurements when determining the thermal resistance of a building and proposes a data pre-processing procedure that allows for the reduction of heat flux fluctuations, which has a significant impact on the final result at low density. The proposed use of wavelet analysis in the pre-processing of low-density heat flux measurement data makes it possible to reconstruct them or reduce disturbances that occur during research. A comparison of the obtained results with the results of the calculation according to ISO 9869-1 showed a decrease in the standard deviation of the measurements from 5.74 to 2.81%. The results of this study can be used to reduce the noise of low-density heat flux and, as a result, reduce the standard deviation of the measurement when applying the HFM method of determining the thermal resistance of external enclosing structures.

1 April 2019
Verified
Conference Paper
Closed access
VBVitalii Babak
Vitalii Babak
ODOleg Dekusha
Oleg Dekusha
LVLeonid Vorobiov
Leonid Vorobiov
LDLeonid Dekusha
Leonid Dekusha
SKSergiy Kobzar
Sergiy Kobzar
SISerhii Ivanov
Serhii Ivanov
The simulation of heat exchange in the working chamber of the device for measuring emissivity was carried. It was shown that the simulation results coincide well with the experimental results. Established that, with the selected technical parameters, the contribution of the conductive-convective component of heat exchange does not exceed 0.1% of the radiation component, and therefore the measurement can be carried out without vacuuming the working chamber. Found suitable area for measurement of emissivity with unevenness of the heat flux distribution, which does not exceed ± 2%.


1 July 2019
Verified
Conference Paper
Closed access
LDLeonid Dekusha
Leonid Dekusha
SKSvitlana Kovtun
Svitlana Kovtun
ODOleg Dekusha
Oleg Dekusha
For industrial control systems, the advantage of directly measuring the heat flux is that, the controlling the parameters of an object at a temperature, only the consequences of thermal action are recorded. The determination of the heat flux can detect a disturbing effect at the initial stage, predict its state and timely correct the mode of operation of the object. The purpose of the work is to provide control of the heat flux in non-stationary conditions with the use of heat flux sensors and to determine the requirements for industrial measurement equipment. From the theoretical and experimental results follows that the use of a modified sensor always gives a gain in time compared with a standard sensor. For study of non-stationary thermal conditions established requirements for the information-measuring system. Given a practical application example of surface heat flux measurements in non-stationary conditions for the control in the flight conditions of the thermal load on elements of the launch vehicle construction.

14 November 2023 in System Research in Energy
Verified
Journal Article
Closed access
PDF file
Artur ZaporozhetsArtur Zaporozhets
Artur Zaporozhets
VBVitalii Babak
Vitalii Babak
GKGanna Kostenko
Ganna Kostenko
ASAnastasia Sverdlova
Anastasia Sverdlova
ODOleg Dekusha
Oleg Dekusha
3B33 B Tov Bud-Bud
33 B Tov Bud-Bud
The quality of living space largely depends on the quality of indoor air. The physical and chemical properties of the air people breathe can affect their health and comfort. Indoor air pollution in residential and workplace environments can occur due to various activities of occupants or employees, such as cooking, smoking, and using electronic devices, as well as emissions of pollutants from building materials and the use of certain products. Pollutants that can be present indoors include carbon monoxide, formaldehyde, volatile organic compounds, particulate matter, aerosols, biological contaminants, and more. To effectively monitor the quality of atmospheric air, it is necessary to determine the main sources of air pollution, which is the purpose of this study. Naturally, the quality of indoor air cannot be clearly separated from the ambient air quality. The first factor affecting the microclimate is the level of air pollution near the building. Air from the street enters the room through windows, doors, or the building's ventilation system. If the state of the surrounding environment is unfavorable, the concentration of harmful substances indoors may also exceed the norm. However, indoor sources of air pollution in any building can have a much greater impact on the health and comfort of the people inside it. Materials used in construction, such as concrete or mineral insulation, may contain ammonia, formaldehyde, and other substances that are released from building structures over time and deteriorate indoor air quality. Ensuring control and monitoring of indoor air quality is an extremely important task. This includes measuring concentrations of pollutants and identifying their sources. It is also important to adhere to standards and recommendations developed by health and environmental organizations to ensure safety and comfort indoors. To reduce indoor air pollution, various measures can be implemented, such as selecting appropriate building materials, and ventilation, installing purification systems, controlling sources of pollution, and limiting the impact of human activity.