18 September 2024 in IEEE Transactions on Instrumentation and Measurement
The integration of projected speckle 3D Digital Image Correlation (3D-DIC) into the field of electronic packaging reliability assessment represents a notable advancement in non-contact measurement techniques. However, the precision of these measurements is frequently compromised by specular reflections from solder balls, particularly when measuring substrate warpage with solder balls attached. To address this issue, this study proposes a method using a Unet-based network for automated identification of substrate areas. This method strategically excludes the solder ball regions from the region of interest (ROI) in DIC calculations, effectively mitigating the effects of reflective interference and thereby enhancing the precision of substrate warpage measurements. Additionally, this study introduces a simple optical method for identifying solder ball regions and compares its error metrics with the proposed Unet-based network enhanced DIC (U-DIC) method, yielding insights into the measurement accuracy and applicable scenarios for each method. Experimental outcomes demonstrate the effectiveness of both methods, as evidenced by a decrease in the mean absolute error of the warpage measurements from approximately 7 μm to approximately 2.6 μm with U-DIC and to 4 μm with the simple method. This development underscores the potential utility of both methods in enhancing the accuracy of reliability assessments in electronic packaging structures.
23 September 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Rough contact creates a large electrical and thermal resistance between the contact surfaces of the electrical connector, which has a great impact on its usage. This work adopted finite element simulation to investigate the electrical and thermal properties in the contact region of electrical connectors. The Weierstras s Mandelbrot fractal function was used to model the contact of crown spring connectors with various roughness. The effects of different roughness and contact force on the electrical and thermal contact performance were analyzed. The increased roughness and decreased contact force cause a reduction in the contact area, resulting in the concentration of current and heat flow. The reduced contact area contributes to the increase of electrical contact resistance and thermal contact resistance. The research indi cates that smoothing the interfaces and increasing the contact force can effectively enhance the contact performance.
15 May 2025 in Measurement Science and Technology
Digital fringe projection (DFP) has been extensively applied in high-precision 3D morphology measurements of advanced electronic packaging. However, under thermal reliability testing, the refractive index variations caused by thermal airflow distort captured fringe images, leading to significant measurement errors. To overcome this challenge, this paper proposes a correction method that integrates the background-oriented Schlieren (BOS) technique with Hamiltonian ray tracing. By reconstructing the 3D refractive index field through multi-angle BOS and applying Hamiltonian optics, light path deviations are accurately estimated and compensated. The corrected images are then used for phase unwrapping and accurate 3D reconstruction. Experimental validations on standard gauge blocks, zirconia ceramics, and BGA chips demonstrate that the proposed method significantly enhances measurement accuracy and repeatability. The phase unwrapping success rate increases from 94.21% to 98.85%, and the artifacts caused by thermal disturbances are largely eliminated. Moreover, statistical analysis of the BGA chip confirms significant reductions in radius and spacing errors of solder balls. This BOS-assisted correction method offers a reliable and low-cost solution for 3D measurements under thermal disturbances, enhancing the performance and robustness of DFP systems in electronic packaging inspection.
4 October 2025 in Optics & Laser Technology
12 September 2025 in IEEE Transactions on Power Electronics
Fan-out panel-level package has become a trend in silicon carbide mosfet packaging due to its superior electrothermal performance and cost-effectiveness. However, the increased size of multichip embedded fan-out panel-level packaging (FOPLP) introduces greater challenges in sample preparation and thermal–mechanical stresses. In this article, a large-sized (20 mm*20 mm*0.78 mm) FOPLP with four SiC mosfets embedded is investigated. A 3-D thermal–mechanical numerical model is derived based on heat conduction and elasticity theories. It utilized analytical solutions of Fourier temperature conduction and finite-difference results for thermoelastic models to describe the temperature and deformation distribution during the FOPLP operation. It also reveals the heat-coupling issue of multiple chips. Compared with the finite-element simulation, the proposed method shows less than 2.5% error in temperature and 2.3% error in deformation. The computational speed is one-tenth that of the finite-element method, while the memory usage is reduced to one-fifth. To mitigate the influence of chip thermal coupling on temperature and warpage, an optimized layout was employed to achieve temperature uniformity improvement. Finally, FOPLPs with the two layouts were fabricated. The warpage was monitored using a digital image correlation platform. To achieve the same temperature, the current required for the optimized layout was increased by 9% . The warpage of the optimized layout at 60 °C was reduced by 13.5%, and at 100 °C, it was reduced by 14.7%, validating the accuracy of the model and the significance of thermal decoupling.
4 August 2026 in Measurement Science and Technology
Accurate identification of polymer materials used in electronic packaging is essential for assembly control, reliability analysis, and counterfeit material detection. However, polymer materials embedded in electronic assemblies are often difficult to identify because they are present in small quantities and consist of heterogeneous composites containing polymer matrices and inorganic fillers. In this study, a measurement framework is developed for identifying polymer materials in electronic packages using Fourier transform infrared spectroscopy with attenuated total reflectance (FTIR-ATR) combined with chemometric analysis. Representative packaging polymers including four underfill materials, two thermal interface materials, and one die attach (DA) adhesive were used to build the classification library. Cross-sectioned package samples were analyzed using micro-ATR FTIR spectroscopy in the fingerprint region (650–1800 cm −1 ), and baseline correction was applied before multivariate analysis. Principal component analysis was used for dimensionality reduction and visualization of spectral clustering, while Soft Independent Modeling of Class Analogy (SIMCA) was used for supervised class modeling and unknown rejection. Using spectra collected from independently prepared package samples, SIMCA correctly classified most test spectra from the modeled library and rejected an external DA material (DA2) as unknown. The results demonstrate that the FTIR-ATR and SIMCA approach provides a rapid and reliable method for identifying polymer materials in electronic packaging and can support applications such as failure analysis, reliability modeling, and material verification.