Aitor Tovar-Barranco

Aitor Tovar-Barranco

Auto-generated profile, based on publicly available information

Aitor Tovar-Barranco

Power Electronics Area, IK4-Ikerlan Technology Research Centre, P°. J.M. Arizmendiarrieta 2, 20500 Arrasate-Mondragón, Spain

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ATAitor Tovar-Barranco
Aitor Tovar-Barranco
ALAmaia Lopez-De-Heredia
Amaia Lopez-De-Heredia
IVIrma Villar
Irma Villar
FBFernando Briz
Fernando Briz
Modeling of convection heat-transfer at the end-windings for thermal networks using lumped-parameters has been widely discussed in the literature. Unfortunately, the resulting coefficients are highly influenced by the end-winding shape, the area in the vicinity of the end-windings, the cooling method of this region (if any), as well by the size and power of the machine. This makes it extremely difficult for the designer to choose a suitable coefficient for the thermal analysis during the design stage of an electric motor. A methodology to obtain the end-windings convection heat-transfer coefficients for fractional-slot concentrated winding permanent-magnet synchronous motors is proposed in this article. Machine designs with both internal and external rotors will be considered. The experimental tests required for the model characterization are described in detail. In this article, general expressions of the convection heat-transfer coefficients between the end-windings and the housing end-caps are proposed for both internal and external rotor designs. Differences observed with the results reported in the literature are also discussed.

3 November 2016
Verified
Conference Paper
Closed access
ATA. Tovar-Barranco
A. Tovar-Barranco
DGD. J. Gomez
D. J. Gomez
ALA. Lopez-De-Heredia
A. Lopez-De-Heredia
IVI. Villar
I. Villar
The size of installed offshore wind turbines is continuously growing every year in an attempt to make this technology more cost-effective. Following this trend, the main challenge for wind turbine manufacturers is to reach the 10 MW power level. However, present topologies of electric generators may have prohibitive mass and volume when designed for such a high power application. In this paper an innovative transverse flux permanent magnet (TFPM) generator topology with a disk shaped rotor is presented with a very high torque density. The design has been performed by means of 3D-FEM software and optimized in order to increase the power factor and reduce the total volume for a 10 MW power goal. The efficiency is later improved by using a higher quality alloy for the construction of the iron cores. The proposed topology is able to reach a torque density of 57.42 kNm/m3.

1 September 2017
Verified
Conference Paper
Closed access
ATAitor Tovar-Barranco
Aitor Tovar-Barranco
FBFernando Briz
Fernando Briz
ALAmaia Lopez-De-Heredia
Amaia Lopez-De-Heredia
IVIrma Villar
Irma Villar

1 September 2016
Verified
Conference Paper
Closed access
DGD. J. Gomez
D. J. Gomez
ATA. Tovar-Barranco
A. Tovar-Barranco
ARA. L. Rodriguez
A. L. Rodriguez
ALA. Lopez-De-Heredia
A. Lopez-De-Heredia
IVI. Villar
I. Villar
Cogging torque produces negative effects in Permanent Magnet Synchronous Machines (PMSMs) such as vibrations, noise and position control inaccuracy. Its impact can be worse due to magnetic saturation when the machine is loaded, increasing its amplitude and causing the magnet or stator slot skew to be ineffective. This paper deals with the study of these phenomena combining a Permeance Network Model (PNM) and the Frozen Permeability (FP) method. With this approach, the actual cogging torque amplitude can be accurately predicted. Furthermore, the optimal skew angle which eliminates the on load cogging torque can be correctly selected. Comparisons between the Maxwell stress tensor and the virtual work principle are also established for the on load cogging torque calculation. It is concluded that the virtual work principle must be employed when using FP technique in a PNM.

1 October 2017
Verified
Conference Paper
Closed access
ATAitor Tovar-Barranco
Aitor Tovar-Barranco
FBFernando Briz
Fernando Briz
ALAmaia Lopez-De-Heredia
Amaia Lopez-De-Heredia
IVIrma Villar
Irma Villar
Torque density of electric motors can be increased if the rotor is placed in the exterior. However, this makes heat extraction more difficult. Study of the thermal behavior at the design stage of the machine can be addressed using FEM and CFD methods. However, they are computationally expensive, and consequently not suitable for the evaluation of multiple designs. A short-time consuming lumped parameter thermal model for external rotor permanent magnet synchronous machines is presented in this work. It allows a fast evaluation of multiple machine design options, being suitable for its use in analytical machine design tools. In addition, comparative analysis of the thermal performance of internal and external rotor designs is provided. The developed model is validated by commercial software achieving good results.