1 March 2018 in Science and Technology of Nuclear Installations
Flash evaporation of a superheated water droplet in heavy liquid metal coolant (lead) is considered, in application to the analysis of a lead-cooled fast reactor steam generator tube rupture accident. The model is based on thermodynamic equilibrium formulation for the expanding water-steam mixture and inviscid compressible formulation for the surrounding liquid lead, with the interface conditions determined from the solution of the Riemann problem. Numerical solution is performed in the spherically symmetric geometry using a conservative numerical scheme with a moving sharp interface. Transient pressure and velocity profiles in each phase are presented for the parameters typical of the steam generator tube rupture accidents, demonstrating the process of boiling water expansion and pressure wave formation in the coolant. The results obtained are compared with a simplified model which considers the volume-averaged parameters of boiling water droplets and considers coolant as an incompressible liquid. Good agreement between the full and simplified models is demonstrated. Impacts of coolant flow on structures caused by pressure wave propagation and subsequent coolant flow are discussed.
29 April 2025 in Thermal Engineering
A review is presented of designs of horizontal steam generators (SG) for nuclear power plants (NPP) with water-moderated water-cooled reactors (VVERs) and of experimental-and-computational studies of thermohydraulic processes running in them. Horizontal SGs are examined from the first commercial design of the PGV-440 SG and the most widely used today PGV-1000M SG to the steam generators developed for the new generation reactor units of types VVER-1200 and VVER-TOI as well as for the high-power VVER-1500 reactor. A comparative analysis was carried out of the experimental facilities developed for the investigation of thermohydraulic processes occurring in a horizontal steam generator. Each of the examined experimental facilities has limitation related to the capabilities for the simulation of a full-scale SG caused by either geometric characteristics or thermohydraulic conditions. Nevertheless, it has been demonstrated that we have at present a sufficiently large experimental database suitable for validating computational codes simulating thermohydraulic characteristics of a horizontal steam generator. A review of the available computational codes is presented. The STEG code in which the two-phase flow is described by multifluid models is examined in more detail. The validation of the STEG code against experimental data on void fraction, pressure drop, and water velocity demonstrated high accuracy of the predictions. One of the problems to be solved in designing horizontal steam generators for new generation reactor units is the improvement of the equalization ability of the submerged and steam-receiving perforated sheets due to the enhanced nonuniformity of the steam load on the evaporation surface and of the steam flow in the steam space. The results are presented of the experimental-and-computational investigation of the equalization ability of perforated sheets, which corroborate the possibility of its improvement by application of a variable perforation ratio. The areas of further experimental investigations into thermohydraulic processes in a horizontal steam generator and ideas for improving the computational codes are formulated.
17 November 2011 in Science and Technology of Nuclear Installations
In the frame of Tacis Project R2.01/99, which was running from 2003 to 2005, the bubble condenser system of Kola NPP (unit 3) was qualified at the integral test facility BC V-213. Three LB LOCA tests, two MSLB tests, and one SB LOCA test were performed. The appropriate test scenarios for BC V-213 test facility, modeling accidents in the Kola NPP unit 3, were determined with pretest calculations. Analysis of test results has shown that calculated initial conditions and test scenarios were properly reproduced in the tests. The detailed posttest analysis of the tests performed at BC V-213 test facility was aimed to validate the COCOSYS code for the calculation of thermohydraulic processes in the hermetic compartments and bubble condenser. After that the validated COCOSYS code was applied to NPP calculations for Kola NPP (unit 3). Results of Tacis R2.01/99 Project confirmed the bubble condenser functionality during large and small break LOCAs and MSLB accidents. Maximum loads were reached in the LB LOCA case. No condensation oscillations were observed.
20 May 2024 in Thermal Engineering
A numerical analysis of the experiments addressed to studies of hydrodynamic processes in a horizontal steam generator has been performed using the STEG (STEam Generator) code. The main components of the experimental model include a staggered tube bundle, a submerged perforated sheet (SPS) with baffles, and a downcomer. An air–water mixture was used as a two-phase fluid. The working fluid flow in the model was driven by natural circulation induced by air supply to the lower, middle, and upper sections of the tube bundle. The gas void fraction was measured by the γ-radiography method. In addition, pressure drops along the height of the tube bundle and water levels in the model and above SPS were also measured. Each experiment was performed at a prescribed air load on the evaporation surface and water level in the model. The STEG code was developed at the Department of Nuclear Power Plants of NRU MPEI to model thermohydraulic processes in a horizontal steam generator. The mathematical model is based on a two-fluid approach to the description of a two-phase flow using balance mass, momentum, and energy conservation equations and semiempirical closing correlations for interfacial interactions and interactions with various surrounding structures (tube bundle, walls, etc.). The STEG code was used to perform calculations for nine experimental regimes differing in the perforation ratio of the submerged perforated sheet and the supplied air flowrate. The qualitative regularities of the two-phase air–water mixture circulation in the model of a horizontal steam generator and the effect of experimental values of the main parameters on the circulation have been established. Quantitative results of comparison of the predictions with the experiment demonstrate their good agreement since the relative errors in the predicted air void fractions and pressure drops do not exceed 10%.
1 December 2023 in Fluid Dynamics
The regularities of the wave of the thermal interaction of water drops in high-temperature molten lead, i.e., a thermal-detonation wave, are studied. Due to the boiling of water on the surface of molten lead, both liquids (phases) are separated by a vapor film. A one-dimensional model of interacting and interpenetrating continua is used, which describes the dynamics of each fluid by introducing a special field characterized by its own velocity, temperature, and volume fraction. The wave velocity is set by the equality of phase velocities and temperatures in the Chapman–Jouguet plane. The parameters at the pressure peak are calculated from the conditions at the discontinuity which are the boundary conditions for integrating the conservation equations in the area of interaction between water droplets and the melt. The resulting structure of the thermal-detonation wave is characterized by the maximum pressure being located at some distance from the shock wave.