21 May 2021 in IEEE Internet of Things Journal
Smartwatch is a potential candidate for the Internet-of-Things (IoT) hub. However, the performance of smartwatch antennas is severely restricted by the smartwatch structure, especially when the antennas are designed by traditional methods. For adapting smartwatches to the role of IoT hub, a novel method of designing the multiband smartwatch antenna is presented in this article, aiming at increasing the number of frequency bands, omnidirectivity, and structural suitability. First, the fundamental structure (including the full screen and the system PCB) of the smartwatch is analyzed as a whole by characteristic mode analysis (CMA). Thus, abundant resources of characteristic modes are introduced. The fundamental structure is then modified as the radiator of a multiband antenna. Then, a nonradiating capacitive coupling element (CCE) excites the desired four 0.5 ${\lambda }$ modes from this structure. This method could fully utilize the intrinsic modes of the smartwatch structure itself, thus exhibiting multiple advantages: significantly small size, smaller ground, omnidirectional radiation, and fitting to the full-screen smartwatch structure.
15 February 2023 in IEEE Transactions on Antennas and Propagation
A monostatic simultaneous transmit and receive (STAR) antenna system consisting of a metasurface-based STAR antenna and two elaborately-designed microstrip-based feeding networks is proposed to suppress the self-interference (SI) from transmission (TX) to reception (RX), a key challenge in STAR design to realize its potential in doubling system capacity. The metasurface antenna is for the first time used in designing a monostatic STAR antenna system for its compact and wideband characteristics. The proposed STAR antenna system possesses the features of monostatic operation, wide bandwidth, high TX/RX isolation, co-circularly polarized radiation with similar patterns for TX and RX, easy fabrication and low cost. The metasurface-based STAR antenna is formed by four dual-polarized metasurface antennas, or units, and is used for both TX and RX to achieve monostatic operation. A wide operating bandwidth is obtained for each antenna unit by combining the resonate modes of the unit and a crossed slot, the feeding structure of the unit, using characteristic mode analysis (CMA). To achieve high TX/RX isolation and identical right-handed circular polarization (RHCP), the four TX and RX ports of the STAR antenna respectively are excited with equal amplitudes and relative phases of 0°, 90°, 180°, and 270°, by two dedicated-designed wideband feeding networks based on the sensitivity analysis. Accordingly, the proposed STAR antenna system is prototyped. The measurement results show that the STAR antenna system achieves >36 dB TX/RX isolation and <3 dB axial ratio from 4.5 to 6 GHz, and maintains similar radiation patterns with the same RHCP for TX and RX.
15 September 2021 in IEEE Transactions on Antennas and Propagation
A wideband monostatic simultaneous transmit and receive (STAR) antenna subsystem with high isolation and Co-horizontally polarized (Co-HP) omnidirectional radiation is presented. The antenna subsystem consists of a STAR antenna and a beamforming network (BFN). The STAR antenna consists of a planar circular array having four printed dipole elements surrounded by two groups of parasitic strips. The parasitic strips are used to improve the impedance bandwidth (IMBW) and reduce the gain variation in transmit (TX) and receive (RX) modes. To achieve high isolation, the four ports of the STAR antenna are excited with two orthogonal phase modes for TX and RX using the BFN. The BFN is a six-port network consisting of two 180° hybrid couplers, one 90° hybrid coupler, and a Wilkinson power divider. The 180° hybrid coupler is elaborately designed with low imbalances since it is most key to achieve high TX/RX isolation. Measured results show that the proposed STAR subsystem achieves a TX/RX overlapping IMBW of 4.71–6.2 GHz, and a 40 dB TX/RX isolation bandwidth of 4.81–5.88 GHz, while maintaining horizontally polarized omnidirectional radiation patterns for TX and RX over the entire operating frequency band.
15 September 2021 in IEEE Transactions on Antennas and Propagation
Dipole antenna is the simplest type of antenna from the theoretical point of view. However, the majority of the research on it focuses on adding supplementary structures to produce more resonant modes to achieve more functions. Here, we focus on the inherent modes of the dipole itself. Dipole antenna has alternating odd and even modes. In classical antenna theory, only odd modes are excited. The even modes are difficult to be excited due to their very high input impedances. In this article, both odd and even modes of the dipole antenna are excited simultaneously by a single port with a novel feeding structure. Moreover, to tune the resonant frequencies of such multiple modes, a method by combining antithetical structures of indentations and outdentations is proposed. Its principle is explained intuitively by eigencurrent distribution. By these new techniques, all the first six modes of a dipole are excited, among which five modes are used for Internet of Things (IoT) applications. The antenna can cover industrial, scientific, and medical (ISM) bands of 868 and 2450 MHz, global navigation satellite system (GNSS) band of 1575 MHz, and 5G bands of 3500 and 4900 MHz. This research could broaden the application of this classic antenna.
14 October 2021 in IEEE Transactions on Antennas and Propagation
This article presents a novel method to design multiple-input–multiple-output (MIMO) antennas based on characteristic mode analysis (CMA), which is different from using individual excitation of each characteristic mode for high isolation. The CMA is performed to design a pair of symmetric slots on two connected dipole antennas (an MIMO dipole pair), so that two desired characteristic modes can be generated at the same frequency, one of which is in common mode and the other in differential mode. Hence, when one antenna element is excited, the two characteristic modes combine and cancel each other at the other antenna element, leading to high port isolation. The designed dipole pair is applied for use in 2G/3G/4G MIMO base-station arrays. The simulation and measurement results show that the antenna achieves a wide impedance bandwidth of 1.7–2.7 GHz (45.5%), low coupling below −20 dB, low cross-polarization below −20 dB, high efficiencies over 85%, and stable radiation patterns within the entire band. The results verified the advances of the proposed decoupling method, i.e., simplicity, effectiveness, wide bandwidth, good radiation, and so on.
15 August 2019 in IEEE Access
In previously published papers about the metal-frame smartphone antennas, the screen is usually not included in the antenna model. As the big-screen, or even full-screen (also called all-screen or bezel-less) smartphones become the trend in recent and foreseeable future years, the effect of the very close screen to metal-frame antennas becomes prominent, e.g., the antenna’s bandwidth is significantly narrowed. In this paper, a metal-frame antenna for the big-screen smartphone covering 824-960 MHz (GSM850/900), 1452-1496 MHz (LTE1500), 1710–2690 MHz (DCS, PCS, UMTS2100, LTE2300/2500), and 3400-3600 MHz (3.5 GHz 5G) is introduced. For the first time, the screen is fully considered, even designed as part of the antenna. The theory of characteristic modes (TCM) is applied in the design method. A prototype is made and measured for verifying the proposed methodology. Some key parameters of this antenna design are also discussed. This methodology helps to improve the degraded performance of smartphone antennas due to the big-screen industrial design.