In this article, we present a set of gallium nitride (GaN) power amplifiers (PAs) that provide state-of-the-art performance within the D-band (110-170 GHz) and G-band (140-220 GHz) frequencies. A four-stage cascode PA operates with more than 25 dB of small-signal gain over a 107-148-GHz band. At 120 GHz, it can deliver up to 26.4 dBm of output power and up to 16.5% of power-added efficiency (PAE) with more than 26 dB of gain at saturation. The combination of these parameters is among the best reported with a solid-state technology at such high frequencies. The two G-band circuits are able to provide up to 40 GHz of 3-dB bandwidth and gain exceeding 10 dB up to 190 GHz. The measured peak output power is 15.8 dBm at 181 GHz in 0.6-dB gain compression with a corresponding PAE of 2.4%. To the best of our knowledge, these amplifiers show the highest gain above 170 GHz and the highest output power above 150 GHz among any reported GaN-based MMICs.
22 March 2021 in IEEE Transactions on Microwave Theory and Techniques
In this article, we summarize the theoretical matching boundaries and show the limitations they implicate for real-world amplifier design. Starting with a common schematic prototype, we investigate the question of how to realize its electrical response in a densely routed, massively parallelized layout. To that end, we develop a comprehensive study on the application of space-mapping techniques toward the design of high-power amplifiers (HPAs). We derive three reference design procedures and compare their performance in terms of convergence, speed, and practicality when laying out a densely routed HPA interstage matching network. Subsequently, we demonstrate the usefulness of the study by designing the networks of a compact three-stage eight-way wideband HPA in the Ka-band. The processed monolithic microwave integrated circuit features a 1-dB large-signal bandwidth of more than 11 GHz (a fractional bandwidth of 32.8%) and thus covers most of the Ka-band with an output power exceeding 6 W in 3 dB of gain compression. This demonstrates the highest combination of power and bandwidth to date using a reactively matched topology in the Ka-band.
This paper reports on the analysis, development and results of a wideband High Power Amplifier (HPA) covering a large segment of the Ka-Band. The presented circuit has been manufactured in a GaN-on-SiC process with a gate length of 100 nm with three different process variants. It reaches a linear gain of well over 22 dB and an output power between 6 and 9 W in the band of 26 to 35 GHz, which equals a fractional bandwidth of over 29 %, while also maintaining a state-of-the-art power-added efficiency. To the best of the authors' knowledge, this is the most broadband HPA over 7 W published in this frequency band.
16 November 2018 in IEEE Transactions on Microwave Theory and Techniques
In this letter, we report on the realization of a two-stage 16-way solid-state power amplifier (SSPA) in the Ka -band. To this end, we describe the design of a high-power amplifier (HPA) in a 100-nm gallium nitride (GaN) process and its integration into a split-block waveguide module. The PA module achieves an output power of more than 7.6 W between 28 and 39 GHz. In conjunction with 16 of these PA modules, we then employed a custom low-loss radial splitter and combiner to create a compact SSPA system. The two-stage SSPA configuration exhibits a small-signal gain of up to 44 dB and a peak output power of 127 W at 31 GHz in 5 dB of gain compression. Furthermore, we measured output power of close to 100 W and state-of-the-art efficiency values of more than 19% between 28 and 38 GHz. To our knowledge, this is the most broadband high-power SSPA demonstrated so far in this frequency range.
30 November 2023 in IEEE Transactions on Electron Devices
In this work, the simultaneously achievable matching bandwidth and output power of AlScN-based high electron mobility transistors (HEMTs) are derived and compared to conventional AlGaN, GaAs, and Si devices. Moll’s method is used to extract time delays resulting in carrier velocities close to 1 $\times$ 10 $^{\text{7}}$ cm/s for sheet carrier densities $\ge$ 1.5 $\times$ 10 $^{\text{13}}$ cm $^{-\text{2}}$ . Subsequently, theoretical current densities of 2.5–4 A/mm and a maximum transconductance higher than 600 mS/mm are derived for low barrier thicknesses of 5–10 nm and Sc-concentrations of 5%–20%. The matching bandwidth is estimated by the Bode–Fano criterion and connected to the output power of the transistor by the power-bandwidth product, which accounts for both parameters simultaneously. AlScN-based devices are found to exhibit a 4.5-times higher power-bandwidth product compared to conventional AlGaN-based HEMTs, quantifying the enormous, theoretical limits. Experimental data already show an improvement by a factor of 1.45 for AlScN-based devices, even in this early stage of development, which proves their superior properties, when aiming for wideband high-power millimeter-wave (mm-wave) devices.