Dong-Joong Kim

Dong-Joong Kim

Auto-generated profile, based on publicly available information

Dong-Joong Kim

Department of Electrical and Biomedical Engineering, Hanyang University, Seoul, South Korea

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HPHae-Chan Park
Hae-Chan Park
MJMin-Woo Ji
Min-Woo Ji
DKDong-Joong Kim
Dong-Joong Kim
Gi-Young LeeGi-Young Lee
Gi-Young Lee
Rae-Young KimRae-Young Kim
Rae-Young Kim
Power factor correction (PFC) converters are utilized extensively across various applications, and therefore, developing customized control algorithms is essential to meet the diverse operational requirements. In critical conduction mode totem-pole PFC technology, introducing harmonic currents into a command signal is a viable approach for enhancing the performance of the PFC converter. However, this approach suffers from the risk of exceeding the planned harmonic current injection because of external interference. To overcome this issue, this article introduces a novel control algorithm that incorporates a harmonic injection technique to maintain stable performance despite disturbances or load variations. This algorithm uses Fourier analysis to precisely calculate each harmonic component and employs proportional-integral compensation along with feedforward corrections method to inject harmonic currents accurately in alignment with theoretical expectations. The efficacy of the proposed algorithm is validated through experiments conducted on a 350 W totem-pole PFC converter prototype under various load conditions. A comparison between the harmonic injection commands determined through a power analyzer and the actual measurements revealed that control was maintained within an error margin of 4.5%, demonstrating that harmonic control was effectively operational even under load variations.

18 September 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
GKGeon Kim
Geon Kim
DKDong-Joong Kim
Dong-Joong Kim
Rae-Young KimRae-Young Kim
Rae-Young Kim
MLMyoung Jin Lee
Myoung Jin Lee
This article investigates the efficiency performance of a current-fed push–pull dc/dc converter incorporating an active-clamp circuit. The primary focus is to optimize the converter’s efficiency by considering the influence of duty ratio and saturation cycling in the boost inductor. The study presents a new efficiency analysis model by incorporating theoretical, simulation, and experimental approaches. Through detailed analysis, the relationship between duty ratio, voltage gain, and efficiency is explored, with an emphasis on achieving high efficiency while minimizing input current ripple. This article defines “saturation cycling” as a phenomenon that inherently arises when the boost inductor alternates between saturated and unsaturated states. This behavior is an unavoidable physical consequence of the design aimed at minimizing input current ripple. The results indicate that it is impossible to simultaneously achieve zero input ripple and maximum efficiency, thus necessitating careful duty ratio selection. Experimental validation confirms that the converter can reach efficiencies of up to 96.565%, demonstrating the robustness and performance of the proposed design. The findings suggest optimal design practices for high-efficiency power conversion in fuel cell applications and similar high-current energy conversion systems.

29 August 2024 in IEEE Access
Verified
Journal Article
Open access
HPHae-Chan Park
Hae-Chan Park
DKDong-Joong Kim
Dong-Joong Kim
KKKun-Hee Kim
Kun-Hee Kim
SMSung-Soo Min
Sung-Soo Min
Rae-Young KimRae-Young Kim
Rae-Young Kim
Active clamp forward (ACF) converters are being extensively applied to auxiliary power modules (APMs) in electric vehicles (EVs) to minimize the use of components and maximize efficiency. Existing ACF converter designs disregard the parasitic characteristics of the components and the leakage inductance of the transformer, resulting in design inaccuracies. This paper proposes a precise design method that considers the transformer impedance and parasitic characteristics of the components. Furthermore, the input–output relationship of the converter, stress on the switching components, and operational range are analyzed to introduce a design strategy that can minimize design errors. Moreover, this study implements a small-signal model and a controller design method based on the contrived model. The proposed design approach is validated through theoretical analysis, simulation comparison, and experimental verification, which includes the accuracy verification of the controller. This approach focuses on markedly reducing design errors, enhancing the precision of the ACF converter design, and further strengthening the reliability of converters for APM of an EV.