A novel analog beamforming technique that utilizes single radio frequency (single-RF) electronically steerable parasitic array radiator (ESPAR) antennas is proposed. The ESPAR beamforming techniques are aimed at precoding in multiple antenna wireless communication systems using the single or hybrid RF approach. One advantage of ESPAR analog beamforming compared to conventional analog beamforming using phase shifters is that arbitrary patterns can be straightforwardly formed. Therefore, ESPAR analog beamforming can provide performance almost identical to digital beamforming. More importantly, ESPAR analog beamforming does not require phase shifters and power splitters, overcoming implementation challenges of conventional analog beamforming. It also has a more compact size compared to conventional beamforming using uniform antenna arrays. We analyze and optimize ESPAR analog beamforming and propose a channel approach based on beamspace pilot transmission to acquire channel state information (CSI). In addition, we propose limited feedback ESPAR analog beamforming based on a beamforming selection strategy. Simulation results for average gain show that ESPAR analog beamforming has almost identical performance to digital beamforming and better performance than analog beamforming using phase shifters. Energy efficiency simulations show that the technique has the highest efficiency among all the beamforming techniques. Therefore, ESPAR analog beamforming has near optimal performance, high energy efficiency, low circuit complexity, low cost, compact size and can be an effective alternative to conventional analog beamforming.
9 September 2025 in IEEE Journal on Selected Areas in Communications
In this paper, we propose an integrated sensing and backscatter communication system utilizing high scanning-rate slot array antennas (SAAs) in a frequency-diverse configuration, leveraging an inverse scattering approach. This system employs a frequency diversity scheme to facilitate rapid spatial data acquisition, significantly outperforming traditional mechanical and electronic scanning methods in terms of speed and cost-efficiency. The proposed integrated system achieves simultaneous localization, identification, and backscatter communication of tags within cluttered environments. Our approach analyzes backscatter process based on the structural and antenna modes of tags, as well as the presence of clutter scatterers. By modulating the tags between open-circuit and short-circuit states, we effectively extract the structural and antenna mode components. The structural mode component allows us to sense both the tags and the surrounding clutter scatterers, while the antenna mode component is used for precise tag identification by incorporating both inverse scattering and compressive sensing (CS) algorithms. During these processes, channel state information (CSI) is gathered through the antenna mode, enhancing the backscatter communication capability of the system. Additionally, the efficacy of backscatter communication is assessed using the bit error rate (BER) with the maximum ratio combining (MRC) technique. Simulations and experimental results demonstrate that our proposed system can accurately sense and identify tags amidst clutter scatterers while maintaining robust backscatter communication over a 40 MHz bandwidth within the 3.98-4.02 GHz range. These results highlight the significant advantages of employing the proposed frequency-diverse antennas and the inverse scattering approach in integrated backscatter communication and sensing applications.
1 April 2025 in IEEE Transactions on Antennas and Propagation
This paper presents a novel integrated sensing, identification, and backscatter communication system that incorporates techniques based on inverse scattering. The proposed system enables simultaneous localization, identification and backscatter communication of tags in cluttered environments. We formulate the backscatter in terms of the tag’s structural and antenna modes and clutter scatterers. By modulating the tags with opencircuit and short-circuit states, we extract the structural and antenna mode components separately. Utilizing the structural mode component, we sense both the tag and clutter scatterers and perform tag identification using the antenna mode component. To conduct sensing and identification both inverse scattering and compressive sensing (CS) algorithms are employed. This enables recovery of high-dimensional imaging information but also significantly reduces the number of transceivers required. In addition, channel state information (CSI) can be acquired by utilizing the antenna mode during the sensing and identification stage, and the backscatter communication performance is evaluated using the bit error rate (BER) based on the maximum ratio combining (MRC) technique. A proof-of-principle illustrative system is developed based on one transmit and one receive array equipped with 3×3 uniform linear antennas (ULA) configuration. Results of sensing, identification and backscatter communication are provided to verify that the proposed system with inverse scattering can accurately locate and identify the tags separately or in combination, while maintaining data communications in challenging cluttered environments.
In this work, we propose a compact millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) system utilizing electronically steerable parasitic array radiator (ESPAR). We analyze the system and channel models for the compact mmWave massive MIMO system using a beamspace formulation and demonstrate that we can optimize the spectral efficiency of the compact mmWave massive MIMO system by jointly adjusting the variable reactive loads in the ESPAR with a digital beamformer. We formulate the compact mmWave massive MIMO system optimization problem to maximize spectral efficiency and propose an unconstrained optimization based algorithm with an initialization method. The spectral and energy efficiencies of the compact mmWave massive MIMO system are evaluated in comparison to conventional mmWave massive MIMO systems of the same antenna size using full-digital, fully-connected hybrid, and partially-connected hybrid beamforming. The results show that the compact mmWave massive MIMO system provides higher spectral efficiency than partially-connected hybrid beamforming. On top of this, it can provide higher energy efficiencies of around 3.21, 2.88, and 1.22 times compared to full-digital, fully-connected hybrid, and partially-connected hybrid beamforming but with lower hardware complexity and lower cost. Therefore, compact mmWave massive MIMO systems are a promising and effective alternative to conventional massive MIMO systems in millimeter wave (mmWave) communications.
This letter introduces an orthogonal frequency division multiplexing differential chaos shift keying (OFDM-DCSK) waveform for communication-centric integrated sensing and communication (ISAC), which simultaneously enables reliable noncoherent communication and robust sensing capabilities. To further address the high peak-to-average power ratio (PAPR) issue of OFDM-based waveforms, a Riemann matrix–based group selected mapping (G-SLM) scheme is incorporated to reduce PAPR under ISAC sensing constraints. The proposed G-SLM achieves significant PAPR improvement compared with conventional SLM methods while requiring no side information at the receiver. Closed-form expressions are derived for the ambiguity function and bit error rate (BER) in the proposed systems with and without G-SLM. Both analytical and simulation results verify that the OFDM-DCSK waveform integrated with G-SLM maintains communication reliability and sensing accuracy compared to the conventional OFDM-DCSK waveform, while reducing the PAPR with only slight main lobes broadening and modest side lobes elevation. These features make the proposed scheme particularly suitable for ISAC applications in complex wireless environments under low and moderate mobility conditions.
12 March 2026 in IEEE Transactions on Mobile Computing
Artificial intelligence is expected to play a central role in enabling future 6 G networks. Developing foundation models that support a wide range of downstream tasks is critical for advancing 6 G standardization. This paper proposes a general framework for compressing wireless channel state information (CSI) using pretrained wireless foundation models. The foundation model is pre-trained using self-supervised learning with a masked reconstruction objective, achieving a normalized mean square error on the order of $10^{-3}$ during pretraining. The model is evaluated on a range of wireless communication and sensing tasks, including classification tasks where compressed CSI is directly used for prediction, and regression tasks that require full CSI reconstruction. For regression tasks such as massive MIMO CSI feedback, the pre-compressed output from the foundation model is used as an auxiliary input to the downstream compressor, effectively enhancing the reconstruction quality. Compared to the Type-I codebook with comparable number of feedback bits, our method improves SGCS by 16.22% and reduces NMSE by 93.24%. Additionally, it achieves comparable SGCS performance to the Type-II codebook while using only 29% of the feedback bits. Comparison with existing research further confirms the contribution of the foundation model's compressed output in improving CSI compression performance. For classification tasks such as WiFi-based human activity recognition and human identification, the compressed representations produced by the foundation model can be directly utilized without additional fine-tuning. These representations achieve over 97% accuracy, outperforming conventional AI-based methods even under higher compression ratios. These findings demonstrate that leveraging a pretrained wireless foundation model consistently enhances performance across both classification and regression tasks, underscoring its versatility and potential in wireless CSI processing.