23 May 2016 in Applied Physics Letters
The effect of the order-disorder transition on the band gap of kesterite Cu2ZnSnS4, an interesting material for solar cells, has been investigated by optical spectroscopy. The band gap energy (Eg) decreases continuously with increasing annealing temperature, Ta, and reaches its minimum at Ta ∼ 273 °C. Eg is about 200 meV higher in the most ordered state, than in the fully disordered state. Its value and the transition kinetic depend on the sample stoichiometry. A simplified model able to explain the order degree and stoichiometry effects on the Eg value is developed. Ordering results in narrower Raman peaks without affecting the shape of the photoluminescence spectrum—except for the change in Eg—or the characteristic energy of the exponential tail below the fundamental absorption edge. Although a prolonged annealing increases the order degree, the material properties are still influenced by residual disorder as well as by defects related to the off-stoichiometry composition.
19 December 2022 in ACS Materials Letters
Pure sulfide kesterite (Cu2ZnSnS4) is one of the most promising emerging photovoltaic technologies thanks to its excellent absorption coefficient, cost-effectiveness, and environmental sustainability. However, record efficiencies are not exceeding 11% due to several issues, such as absorber defects or a nonoptimal band alignment with the toxic but conventionally used CdS buffer layer. To get rid of it, several efforts have been made in the past few years. Among recent theoretical works, TiO2 has been suggested as a suitable buffer layer due to its optical and electrical properties, giving extremely promising results in device simulation. However, there are few experimental examples combining TiO2 with kesterite, and they generally show very modest performances. In this Letter, we report on the preliminary and promising results of our experimental procedure for the production of Cd-free kesterite photovoltaic devices featuring ALD-TiO2 as a buffer layer, leading to efficiencies comparable with our CZTS/CdS reference devices.
25 December 2024 in Ceramics International
1 July 2015 in Journal of Renewable and Sustainable Energy
A new approach based on hot injection method is proposed to gram-scale Cu2ZnSnS4 nanoparticles production minimizing the use of organic solvents. Nanocrystal synthesis was performed starting from metal chlorides and pure sulphur powder and using Oleylamine as capping agent. As a result, core-shell nanoparticles with a narrow size distribution were obtained.
1 May 1988 in Journal of Applied Physics
Asymmetrical light and electron beam induced current profiles have been previously attributed to a difference of the diffusion length on the two sides of the grain boundary. We show that this feature is instead due to the grain boundary not being perpendicular to the surface. In this geometry, the equations describing the minority‐carrier diffusion are not solvable by analytical procedures. A method for their numerical solution is hereby introduced, fast enough to allow the use of minimization procedures. A good agreement has been found between fitted values of the grain boundary inclination and those directly measured.
1 October 2022 in Journal of Physics: Energy
The addition of alkali elements has become mandatory for boosting solar cell performance in chalcogenide thin films based on kesterites (Cu2ZnSnS4, CZTS). A novel doping process is presented here, that consists in the incorporation of sodium or lithium during the deposition of the CdS buffer layer, followed by a post-deposition annealing (PDA). As the doping route leads to more efficient devices in comparison with the undoped reference sample, the influence of PDA temperature was also investigated. Compositional profiling techniques, time-of-flight secondary ion mass spectrometry (TOF-SIMS) and glow discharge optical mission spectroscopy (GDOES), revealed a dependence of the alkaline distribution in kesterites with the PDA temperature. Although the doping process is effective in that it increases the alkaline concentration compared to the undoped sample, the compositional profiles indicate that a significant proportion of Li and Na remains ‘trapped’ within the CdS layer. In the 200 °C–300 °C range the alkali profiles registered the higher concentration inside the kesterite. Despite this, an additional alkali accumulation close to the molybdenum/fluorine doped tin oxide substrate was found for all the samples, which is frequently related to alkali segregation at interfaces. The addition of both, lithium and sodium, improves the photovoltaic response compared to the undoped reference device. This is mainly explained by a substantial improvement in the open-circuit potential (V oc) of the cells, with best devices achieving efficiencies of 4.5% and 3% for lithium and sodium, respectively. Scanning-electron microscopy images depicted a ‘bilayer structure’ with larger grains at the top and small grains at the bottom in all samples. Moreover, the calculated bandgap energies of the CZTS films account for changes in the crystallographic order-disorder of the kesterites, more related to the PDA treatment rather than alkali incorporation. Even if further optimization of the absorber synthesis and doping process will be required, this investigation allowed the evaluation of a novel strategy for alkali incorporation in kesterite based solar cells.