Camilo Quintans

Camilo Quintans

Auto-generated profile, based on publicly available information

Camilo Quintans

Department of Electronics Technology, Universidade de Vigo, 36310 Vigo, Spain

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2016 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
CQCamilo Quintáns
Camilo Quintáns
RIRamiro Iglesias
Ramiro Iglesias
ALAlfonso Lago
Alfonso Lago
JAJorge Marcos Acevedo
Jorge Marcos Acevedo
CMCarlos Martínez-Peñalver
Carlos Martínez-Peñalver
In order to design power circuits including supercapacitors, a model that responds as closely as possible to results in actual tests, in both fast and slow transients, is required. The network of the parallel RC branches model is widely used to justify the electrical behavior of supercapacitors. In that model, in order to achieve a good fitting between simulation and actual transient responses, the interdependence among the parameters, as well as their voltage dependence, must be considered. This study presents a method to deduce the parameters of the RC network model through the transient response of the supercapacitor including theirs voltage dependence. The methodology considers that the electrical charge provided to the device in the current pulses is not only injected in the fastest branch, but also is simultaneously distributed toward the slower branches. A set of tests have been carried out through the whole voltage range of the device in such a way that in each one the parameters can be considered constant. Then, with the obtained series of values for each parameter, their voltage dependence has been deduced through linear regression. Practical results of a fourth-order model with voltage-dependent parameters are presented and compared with simulations.

7 April 2006
Verified
Conference Paper
Closed access
CQC. Quintans
C. Quintans
VAValdes
Valdes
MMM.J. Moure
M.J. Moure
LFL. Fernandez-Ferreira
L. Fernandez-Ferreira
EME. Mandado
E. Mandado

8 January 2010 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
CSCelso F. Silva
Celso F. Silva
CQCamilo Quintans
Camilo Quintans
Antonio Colmenar-SantosAntonio Colmenar-Santos
Antonio Colmenar-Santos
MCManuel A. Castro
Manuel A. Castro
EMEnrique Mandado
Enrique Mandado
This paper presents a method to implement reconfigurable logic controllers (RLCs) using a new matrix model to describe Petri nets (PNs). The method obtains the general equations and directly translates them into a hardware description language (HDL) to configure a field-programmable gate array (FPGA). To achieve a generalized model in a comprehensible way, several PN examples including timers, counters, and hierarchical subnets are described in detail. The working principles and robustness of the method are validated by simulating each example and by their practical implementation in an RLC.

12 February 2020 in IEEE Sensors Journal
Verified
Journal Article
Closed access
CQC. Quintans
C. Quintans
JAJorge Marcos Acevedo
Jorge Marcos Acevedo
CMC. Martinez-Penalver
C. Martinez-Penalver
This paper presents the development of a low-power electronic system powered by a thermoelectric generator, based on Peltier cells, which takes advantage of daily temperature variations in the environment using a tank with 6 liters of water as a thermal accumulator. The generator works both day and night, since it uses a dc-dc boost converter with bipolar input. The system avoids using batteries because it charges a 0.1 F supercapacitor module between 2.40 and 3.15 V, so the useful energy in each charging cycle is 208 mJ. This energy is sufficient so that the system can measure the ambient temperature, represent it on a display and record it along with the date and time on a memory card when there is enough stored energy. The PSpice model and the simulation of the generator is also presented and experimental results of its operation are presented for two days. It is derived that in that period, with a maximum temperature difference of 10 °C, the system is able to charge the supercapacitor thirteen times per day, which means a daily useful energy of 2.7 J. Finally, results of the autonomous system performance for four days are presented.

1 November 2006 in IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics
Verified
Conference Paper
Closed access
CSCelso F. Silva
Celso F. Silva
CQCamilo Quintans
Camilo Quintans
JLJose M. Lago
Jose M. Lago
EMEnrique Mandado
Enrique Mandado
At present, logic controllers use sequential programmable logic controllers (PLC) and industrial computers with scan strategies and special instructions for parallel events detection. Also, nowadays, reconfigurable devices improvement allows the implementation of parallel control strategies in a more natural way. This paper describes an integrated system for logic controller implementation using FPGA. It consists of a hardware card and a design automation environment which improves design performance. The hardware, as well as doing typical automation tasks, contributes to achieving additional characteristics such as simulation and monitoring. To show the integrated system applications, a real industrial project is undertaken

1 June 2007
Verified
Conference Paper
Closed access
CQCamilo Quintans
Camilo Quintans
JAJorge Marcos Acevedo
Jorge Marcos Acevedo
GCGerardo Castro
Gerardo Castro
AMAndres Augusto Nogueiras Melendez
Andres Augusto Nogueiras Melendez
This work presents a software tool in order to facilitate the learning of the dc choppers. This tool consists of an integrated web-access set of multimedia animation-clips which present, in an interactive way, how the different dc choppers topologies work. The different topologies are classified depending on their quadrant operation and then the user can realize the circuit's performance from the simplest class-A to the four quadrant operation class-E converter. To do this, all circuit parameters including load values, duty ratio, and frequency may be selected by the user. Moreover, the load includes an electromotive force (EMF) that allows understanding the energy flow between the source and the load and then, the quadrant operation. Other useful characteristic of the tool is the way in which the circuits are drawn because they can be shown as a bridge or in their simplest form in the case of only the essentials devices being shown. The information about the currents and voltages paths is dynamically presented with sliding rules over the graphs during simulations indicating the state of semiconductor switches by means of changing colours. The multimedia system includes documentation on all the subjects, showing basic concepts and equations, in pdf format and links to industrial manufacturers.