Anbalagan Sathishkumar

Anbalagan Sathishkumar

Auto-generated profile, based on publicly available information

Anbalagan Sathishkumar

Department of Mechanical Engineering, SRM Institute of Science and Technology, Chennai, India

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 August 2025 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
ASA. Sathishkumar
A. Sathishkumar
SPSundaram P
Sundaram P
RPRajendran Prabakaran
Rajendran Prabakaran
MCM. Cheralathan
M. Cheralathan
JKJae-Hyun Kim
Jae-Hyun Kim
SKSung Chul Kim
Sung Chul Kim

1 September 2023 in Arabian Journal of Chemistry
Verified
Journal Article
Open access
PPPragathi Pandian
Pragathi Pandian
PSPalanichamy Sundaram
Palanichamy Sundaram
ASAnbalagan Sathishkumar
Anbalagan Sathishkumar
RPRajendran Prabakaran
Rajendran Prabakaran
PKPoongavanam Ganesh Kumar
Poongavanam Ganesh Kumar
MRMuraliraja Rajaraman
Muraliraja Rajaraman

14 January 2022 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
ASA. Sathishkumar
A. Sathishkumar
MCMarimuthu Cheralathan
Marimuthu Cheralathan
This research paper describes the experimental investigation of the phase change characteristics of deionized (DI) water with the addition of functionalized graphene nanoplatelets (FGNP) in a spherical container used in cool thermal energy storage (CTES) systems. The nano-enhanced phase change materials (NEPCMs) are developed by the dissolution of FGNP in the mass concentrations of 0.25%, 0.50%, and 0.75% with DI water. The thermal conductivity (TC) and phase change enthalpy (H) of the NEPCMs were measured experimentally using the transient hot-wire method and DSC 214 polymer, respectively. At heat transfer fluid (HTF) temperatures of −10°C and 15°C, the mass fraction of 0.75 improves thermal conductivity by 48.2% and 33.2% in the solid and liquid phases, respectively. At a heating rate of 1K min-1, the addition of FGNP significantly reduces the H of the base PCM in both crystallization and melting processes. The maximum reduction in crystallization and melting time was recorded to be 32.4% and 52.4% in a spherical container with the addition of maximum concentration of FGNP at the HTF temperatures of −8°C and 25°C, respectively.

22 January 2026 in Energy Conversion and Management
Verified
Journal Article
Closed access
PDPalanisamy Dhamodharan
Palanisamy Dhamodharan
EMEd Joshua Manalac
Ed Joshua Manalac
RPRajendran Prabakaran
Rajendran Prabakaran
ASAnbalagan Sathishkumar
Anbalagan Sathishkumar
SKSung Chul Kim
Sung Chul Kim

28 April 2023 in Fullerenes, Nanotubes and Carbon Nanostructures
Verified
Journal Article
Closed access
PPPragathi P.
Pragathi P.
SPSundaram P
Sundaram P
ASA. Sathishkumar
A. Sathishkumar
GPGanesh Kumar Poongavanam
Ganesh Kumar Poongavanam
The concept of reuse and recycling has undergone sustained development in industries to prevent the exhaustion of naturally available resources. The current study is about reusing spent catalyst waste from petroleum refining industries as reinforcement in aluminum composite materials. This work utilized the stir casting method to create nano B4C/waste spent catalyst/Al matrix composites by varying the B4C from 0.5 to 2.0 wt% and maintaining the constant 10 wt% of spent catalyst waste, respectively. Furthermore, the impact of nano B4C and spent catalyst waste on the mechanical and microstructure behavior of aluminum matrix hybrid composites were studied. The compressive strength, hardness, and tensile strength of the aluminum composites obtained with different percentages of nano B4C and spent catalyst waste were enhanced significantly. The increase in tensile strength mainly due to the effect of the Orowan strengthening mechanism and thermal stresses caused by the difference in the CTE of aluminum matrix and reinforcement. The effective mechanical behavior was obtained with 1.5 wt% B4C and 10 wt% spent catalyst waste with massive improvements in hardness (65.62%), compressive (31.81%), and tensile strength (48.23%), respectively, compared to base pure aluminum.

27 November 2025 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
RPRajendran Prabakaran
Rajendran Prabakaran
PDPalanisamy Dhamodharan
Palanisamy Dhamodharan
ASAnbalagan Sathishkumar
Anbalagan Sathishkumar
RDRamasamy Dhivagar
Ramasamy Dhivagar
SKSung Chul Kim
Sung Chul Kim