Knut Eilif Aasmundtveit

Knut Eilif Aasmundtveit

Auto-generated profile, based on publicly available information

Knut Eilif Aasmundtveit

Department of microsystems, University of South-Eastern Norway, 3184 Horten, Norway

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 March 2023 in Polymers
Verified
Journal Article
Open access
PDF file
NDNu Bich Duyen Do
Nu Bich Duyen Do
KIKristin Imenes
Kristin Imenes
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit
HNHoang-Vu Nguyen
Hoang-Vu Nguyen
EAErik Andreassen
Erik Andreassen
Materials providing heat dissipation and electrical insulation are required for many electronic and medical devices. Polymer composites with hexagonal boron nitride (hBN) may fulfil such requirements. The focus of this study is to compare composites with hBN fabricated by injection moulding (IM), powder bed fusion (PBF) and casting. The specimens were characterised by measuring thermal conductivity, tensile properties, hardness and hBN particle orientation. A thermoplastic polyurethane (TPU) was selected as the matrix for IM and PBF, and an epoxy was the matrix for casting. The maximum filler weight fractions were 65%, 55% and 40% for IM, casting and PBF, respectively. The highest thermal conductivity (2.1 W/m∙K) was measured for an IM specimen with 65 wt% hBN. However, cast specimens had the highest thermal conductivity for a given hBN fraction. The orientation of hBN platelets in the specimens was characterised by X-ray diffraction and compared with numerical simulations. The measured thermal conductivities were discussed by comparing them with four models from the literature (the effective medium approximation model, the Ordóñez-Miranda model, the Sun model, and the Lewis-Nielsen model). These models predicted quite different thermal conductivities vs. filler fraction. Adding hBN increased the hardness and tensile modulus, and the tensile strength at high hBN fractions. The strength had a minimum as the function of filler fraction, while the strain at break decreased. These trends can be explained by two mechanisms which occur when adding hBN: reinforcement and embrittlement.

31 March 2015 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
TLThi-Thuy Luu
Thi-Thuy Luu
NHNils Hoivik
Nils Hoivik
KWKaiying Wang
Kaiying Wang
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit
AVAstrid-Sofie B. Vardøy
Astrid-Sofie B. Vardøy

1 August 2013
Verified
Conference Paper
Closed access
HNHuy Quoc Nguyen
Huy Quoc Nguyen
BTBao Ta
Bao Ta
NHNils Hoivik
Nils Hoivik
EHEinar Halvorsen
Einar Halvorsen
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit
With increasing pressure on food industry to reduce waste while meeting the demand for high food quality and safety, there is a strong motivation for research into sensors for monitoring freshness and general food quality. Degradation of fresh meat and produce is related to metabolic activities of microorganisms which commonly result in formation of gaseous compounds such as CO 2 . Monitoring the freshness and quality of the food can therefore be accomplished by monitoring the release of these gases in the food package. In this study, an approach to create sensors for detecting gases released by perished food is described. Sensor test is conducted with CO 2 which is a common gas related to the degradation process of food. The sensor is based on Carbon Nanotubes (CNTs) as sensing elements. A local synthesis technique is used to directly integrate the CNTs onto silicon-based circuits at room temperature. Fabricated CNT-based structures have successfully demonstrated the ability to detect CO 2 . The sensitivity and selectivity of gas sensors to different gas compounds were also studied. The results indicate that this approach is promising for fabrication of CNT-based gas sensors at low cost for determination of food freshness and quality, making possible complete gas sensors including CNT sensing elements, CMOS signal processing and RF communication on the same chip, manufactured and integrated at the wafer-level scale.

22 July 2019 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
ALAndreas Larsson
Andreas Larsson
TTTorleif A. Tollefsen
Torleif A. Tollefsen
OLOle Martin Løvvik
Ole Martin Løvvik
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit

30 May 2018
Verified
Book Chapter
Open access
PDF file
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit
TLThi-Thuy Luu
Thi-Thuy Luu
HNHoang-Vu Nguyen
Hoang-Vu Nguyen
ALAndreas Larsson
Andreas Larsson
TTTorleif A. Tollefsen
Torleif A. Tollefsen
Solid-liquid interdiffusion (SLID) bonding for microelectronics and microsystems is a bonding technique relying on intermetallics. The high-melting temperature of intermetallics allows for system operation at far higher temperatures than what solder-bonded systems can do, while still using similar process temperatures as in common solder processes. Additional benefits of SLID bonding are possibilities of fine-pitch bonding, as well as thin-layer metallurgical bonding. Our group has worked on a number of SLID metal systems. We have optimized wafer-level Cu-Sn SLID bonding to become an industrially feasible process, and we have verified the reliability of Au-Sn SLID bonding in a thermally mismatched system, as well as determined the actual phases present in an Au-Sn SLID bond. We have demonstrated SLID bonding for very high temperatures (Ni-Sn, having intermetallics with melting points up to 1280°C), as well as SLID with low process temperatures (Au-In, processed at 180°C, and Au-In-Bi, processed at 90–115°C). We have verified experimentally the high-temperature stability for our systems, with quantified strength at temperatures up to 300°C for three of the systems: Cu-Sn, Au-Sn and Au-In.

7 May 2024 in Advanced Materials Technologies
Verified
Journal Article
Open access
VHVan Long Huynh
Van Long Huynh
KAKnut E. Aasmundtveit
Knut E. Aasmundtveit
HNHoang-Vu Nguyen
Hoang-Vu Nguyen
Anisotropic conductive adhesives (ACAs) are the preferred interconnection technology for applications that employ large dies, flexible substrates, and ultra fine‐pitch interconnects. Conventional ACAs require relatively high bonding pressures and temperatures, and ultra fine‐pitch applications challenge the trade‐off between low interconnect resistance and risk of short circuits. This study introduces an ACA‐like interconnection technology that addresses these limitations, allowing for low‐pressure, low‐temperature assembly processes with enhanced particle control at the interconnects. Conductive particles are deposited onto a patterned carrier and subsequently transferred to electrical pads using either non‐conductive film or Ag sintering. The Ag sintering process is performed at a low temperature (140 °C) and low bonding pressure (1 N for a 10 × 10 mm2 chip). The capability of controlling the position and number of conductive particles within individual interconnects is demonstrated. This presents possibilities for achieving ultra‐fine pitch interconnects with negligible risk of short circuits, without compromising electrical resistance. It is demonstrated that interconnect resistance can be tuned by varying the number of conductive particles (achieving a resistance as low as 33 mΩ with 25 particles per interconnect). This approach is applicable to scenarios where the bonding force and temperature must remain low due to the nature of substrate materials.