One of the inherent challenges with Li–S batteries is polysulfide dissolution, in which soluble polysulfide species can contribute to the active material loss from the cathode and undergo shuttling reactions inhibiting the ability to effectively charge the battery. Prior theoretical studies have proposed the possible benefit of defective 2 D MoS2 materials as polysulfide trapping agents. Herein the synthesis and thorough characterization of hydrothermally prepared MoS2 nanosheets that vary in layer number, morphology, lateral size, and defect content are reported. The materials were incorporated into composite sulfur‐based cathodes and studied in Li–S batteries with environmentally benign ether‐based electrolytes. Through directed synthesis of the MoS2 additive, the relationship between synthetically induced defects in 2 D MoS2 materials and resultant electrochemistry was elucidated and described.
22 April 2022 in Physical Chemistry Chemical Physics
Combining calorimetry with hard and soft X-ray characterization elucidates bulk and surface phenomena responsible for capacity fade in LiNi0.8Mn0.1Co0.1O2 cathodes.
30 September 2020 in Physical Chemistry Chemical Physics
The phase distribution of lithiated LVO in thick (∼500 μm) porous electrodes (TPEs) designed to facilitate both ion and electron transport was determined using synchrotron-based operando energy dispersive X-ray diffraction (EDXRD). Probing 3 positions in the TPE while cycling at a 1C rate revealed a homogeneous phase transition across the thickness of the electrode at the 1st and 95th cycles. Continuum modelling indicated uniform lithiation across the TPE in agreement with the EDXRD results and ascribed decreasing accessible active material to be the cause of loss in delivered capacity between the 1st and 95th cycles. The model was supported by the observation of significant particle fracture by SEM consistent with loss of electrical contact. Overall, the combination of operando EDXRD, continuum modeling, and ex situ measurements enabled a deeper understanding of lithium vanadium oxide transport properties under high rate extended cycling within a thick highly porous electrode architecture.
The chemical interactions in Fe–HfH2 metal matrix composites (MMCs) are studied across multiple length scales to elucidate the decomposition of the parent phases and corresponding reaction zone physics during direct current sintering. Fe–HfH2 composites were synthesized with increasing as-mixed hydride contents of Fe–25% HfH2, Fe–40% HfH2, Fe–55% HfH2, and Fe–70% HfH2 (all in vol. %) to demonstrate the ability to achieve sintered MMCs with target hydride contents. Samples were probed across multiple length scales through a multi-modal workflow employing x-ray diffraction, scanning electron microscopy and segmentation analysis, and synchrotron techniques including hard x-ray fluorescence mapping and nanoprobe x-ray absorption near-edge structure measurements. Under the selected sintering temperature and pressure conditions, hydrogen evolution is seen to evolve through parallel paths: thermal decomposition from during the transformation of HfH2 to HfHx<2 and through subsequent reaction with the Fe matrix leading to intermetallic phase formation. Specifically, HfFe and HfFe2 intermetallic formation accelerates the release of hydrogen with a subsequent HfO2 phase forming at grain boundaries. For this MMC, the consumption or loss of hydrogen can be considerable in compacts with initial hydride loading of 25%–40% HfH2 approaching 83% hydrogen loss for the lower volume fraction composites. Increasing the volume fraction of HfH2 to 70% enhanced the retained hydrogen content to 53% and attributed to the reduced interfacial area intrinsic to the increased HfH2 loading in this MMC.
The Cover Feature shows the synthesis and thorough characterization of hydrothermally prepared MoS2 nanosheets that vary in layer number, morphology, lateral size, and defect content. The materials were incorporated into composite sulfur‐based cathodes and studied in Li–S batteries with environmentally benign ether‐based electrolytes. Through directed synthesis of the MoS2 additive, the relationship between synthetically induced defects in 2 D MoS2 materials and resultant electrochemistry was elucidated. More information can be found in the Full Paper by A. Abraham et al.