Key Laboratory of Advanced Micro/Nano Electronic Devices and Smart Systems of Zhejiang, College of Information Science and Electronic Engineering, Zhejiang University 1 , Hangzhou 310027, China
Auto-generated profile, based on publicly available information
Shuyi Huang
Key Laboratory of Advanced Micro/Nano Electronic Devices and Smart Systems of Zhejiang, College of Information Science and Electronic Engineering, Zhejiang University 1 , Hangzhou 310027, China
Here we demonstrate a magnetic resonance coupling based wireless triboelectric nanogenerator (TENG) and fully self-powered wireless sensors. By integrating a microswitch and an inductor with the TENG, the pulsed voltage output is converted into a sinusoidal voltage signal with a fixed frequency. This can be transmitted wirelessly from the transmit coil to the resonant-coupled receiver coil with an efficiency of 73% for a 5 cm distance between the two coils (10 cm diameter). Analytic models of the oscillating and coupled voltage signals for the wireless energy transfer are developed, showing excellent agreement with the experimental results. A TENG of 40 × 50 mm2 can wirelessly light up 70 LEDs or charge up a 15 μF capacitor to 12.5 V in ~90 s. The system is further utilized for two types of fully self-powered wireless chipless sensors with no microelectronic components. The technologies demonstrate an innovative strategy for a wireless ‘green’ power source and sensing.
A flexible surface acoustic wave (SAW) strain sensor in the frequency range of 162–325 MHz was developed based on a single crystalline LiNbO3 thin film with dual resonance modes, namely, the Rayleigh mode and the thickness shear mode (TSM). This SAW sensor could handle a wide strain range up to ±3500 owing to its excellent flexibility, which is nearly six times the detecting range of bulk piezoelectric substrate based SAW strain sensors. The sensor exhibited a high sensitivity of 193 Hz/ with a maximum hysteresis less than 1.5%. The temperature coefficients of frequency, for Rayleigh and TSM modes, were −85 and −59 ppm/ , respectively. No visible deterioration was observed after cyclic bending for hundreds of times, showing its desirable stability and reliability. By utilizing the dual modes, the strain sensor with a self-temperature calibrated capability can be achieved. The results demonstrate that the sensor is an excellent candidate for strain sensing.
Langasite (LGS) surface acoustic wave (SAW) temperature sensors have a large second order temperature coefficient of frequency, which leads to their non-linear and non-monotonic responses in a wide temperature range and possibly makes the measured temperatures non-unique for a specific sensor response. Here, we propose a high-temperature Pt/LGS SAW sensor with linear frequency–temperature behavior in a wide temperature range, which was fabricated on a LGS (0°, 138.5°, 72°) substrate. The sensor has a single acoustic mode, but dual resonances with similar second- and third-order temperature sensitivities that were utilized for achieving a linear frequency–temperature response by a method of difference. A linear relationship between the measured sensor output (Δfm21) and temperature was obtained in the range of −60 °C to 700 °C, consistent with the theoretical analysis. The sensor has a high sensitivity of −167 ppm/K for the whole temperature range. All the results demonstrated exciting prospects of the sensor for wide temperature monitoring in harsh environments.
26 June 2022 in ACS Applied Materials & Interfaces
Memristors are an important component of the next-generation artificial neural network, high computing systems, etc. In the past, two-dimensional materials based memristors have achieved a high performance and low power consumption, though one at the cost of the other. Furthermore, their performance can not be modulated frequently once their structures are fixed, which remains the bottleneck in the development. Herein, a series of forming free memristors are fabricated with the same Cu/Fe 3 GeTe 2 oxide/Fe 3 GeTe 2 /Al structure, yet the On/Off ratio and set voltage is modulated continuously by varying the oxidation time during fabrication. With an optimal oxidation time, a large On/Off ratio (1.58 × 10 3 ) and low set voltage (0.74 V) is achieved in a single device. The formation and rapture of Al conductive filaments are found to be responsible for the memristors, and the filaments density and the cross-section area increase with the increase of current compliance, which achieves a higher On/Off ratio. The memristor can imitate basic biological synaptic functions using voltage pulses, demonstrating the potential for low-power consuming neuromorphic computing applications.