3 March 2016 in Journal of Materials Chemistry A
A highly-porous, binder free 3D-NiCo 2 O 4 /Ni nanostructure on the Ni-wire was fabricated for flexible fiber supercapacitors. The fabricated device exhibited enhanced capacitance, high efficiency, good cycling stability, and flexibility.
30 December 2020 in IEEE Journal of Solid-State Circuits
An 8-bit 1-GS/s asynchronous loop-unrolled (LU) successive approximation register (SAR)-Flash hybrid analog-to-digital converter (ADC) with complementary dynamic amplifiers (CDAs) is presented. The proposed ADC is a combination of an asynchronous LU-SAR ADC and a reference-embedding 8x interpolating flash (I-Flash) ADC to enhance the conversion speed. Operating the CDAs in a dual-edge manner makes it possible to achieve an 8-bit resolution with only four CDAs and one capacitive digital-to-analog converter (C-DAC), which improves the power and area efficiency as well as the input bandwidth. A prototype ADC implemented in a 28-nm CMOS process occupies a 0.002 mm² active area. The measured differential non-linearity (DNL) and integral non-linearity (INL) after offset calibration is 0.59 and 0.82 LSB, respectively. With a 0.499-GHz input, the measured signal-to-noise and distortion ratio (SNDR) and the spurious-free dynamic range (SFDR) are 45.5 and 59.4 dB, respectively. The measured effective resolution bandwidth (ERBW) is above 3 GHz. The power consumption at 1-GS/s conversion is 2.55 mW with a supply voltage of 1.1 V, leading to a figure of merit (FoM) of 16.6 fJ/conversion-step.
21 June 2018 in IEEE Journal of Solid-State Circuits
This paper presents a two-way time-interleaved (TI) 12-b 270-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) with a virtual-timing-reference timing-skew calibration scheme, in which the timing-skew calibration spurs present in conventional calibration schemes are effectively suppressed with the deferred reference sampling edge. The proposed design runs in a true background mode of operation, whose accuracy is independent of the statistics and the wide-sense stationary property of the input. A 12-b 270-MS/s prototype ADC with the on-chip timing-skew and offset calibration circuits is fabricated in a 40-nm CMOS process, where the timing-skew calibration circuits occupy only 9.7% of the total core area, showing the simplicity and ease of integration of the calibration algorithm even in large-scale TI ADCs. The prototype achieves a peak SNDR of 60.2 dB and a Nyquist-rate SNDR of 59.7 dB while consuming 4.5 mW from a 0.9-V supply, which then results in a Walden FoM of 21.1 fJ/conversion-step.
5 October 2018 in IEEE Journal of Solid-State Circuits
A 6-bit 2.5-GS/s 8x dynamic interpolating flash analog-to-digital converter (ADC) with an offset calibration technique for interpolated voltage-to-time converters (VTCs) is presented for high-speed applications. The dynamic-amplifier-structured VTC enables linear zero-crossing (ZX) interpolation in the time domain with an interpolation factor of 8, which reduces the number of front-end VTCs to one-sixth the original structure. The reduced number of VTCs lowers the power consumption, load capacitance to the track-and-holder (T/H), and overhead of VTC offset calibration. The sequential slope-matching offset calibration scheme is proposed not only for VTC offset but also for interpolated ZX accuracy. The prototype 6-bit 2.5-GS/s flash ADC was implemented in a 65-nm CMOS process and occupies a 0.12 mm² chip area, including offset calibration circuitry. The measured differential non-linearity (DNL) and integral non-linearity (INL) after offset calibration are 0.68 and 0.65 LSB, respectively. With a 1.23 GHz input, the measured signal-to-noise and distortion ratio (SNDR) and spurious-free dynamic range (SFDR) are 33.84 and 45.07 dB, respectively, with power consumption of 7.5 mW under a supply voltage of 0.85 V. The prototype ADC achieves a figure of merit (FoM) of 74.7 fJ/conversion step at 2.5 GS/s.
4 April 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief proposes a code-reusable design methodology for synthesizable successive approximation register (SAR) ADCs based on the digital design flow to significantly reduce design effort. The SAR ADCs are composed of a capacitor-DAC (CDAC) macro cell generated by a CDAC compiler and analog functional blocks implemented utilizing digital standard cells. Two prototypes of SAR ADCs (12-bit 100 kS/s and 11-bit 50 MS/s) are fabricated in different CMOS processes (180 nm and 28 nm). The prototype ADCs prove the effectiveness of the proposed design methodology with comparable performances with full-custom designed SAR ADCs.
30 April 2021 in IEEE Journal of Solid-State Circuits
This article presents a relative-prime-based time-interleaved (RP TI) sub-ranging successive-approximation register (SAR) analog-to-digital converter (ADC) with on-chip background skew calibration. The proposed calibration aligns the sampling time of every fine ADC (F-ADC) to that of a particular coarse ADC (C-ADC) that works as a reference ADC. To avoid the unwanted calibration tone from the reference ADC, the C-ADC is also time-interleaved to make all samples undergo the same kick back. By setting the numbers of the time-interleaved channels of the C-ADCs and F-ADCs in a relative-prime relationship, every C-ADC can be evenly shared by every F-ADC; thus, the timing skews between the interleaved sub-ADCs are calibrated by adjusting the sampling edges of every F-ADC to the particular C-ADC working as a reference ADC. An 18-channel TI 10-bit 2.2-GS/s SAR ADC was implemented as a prototype with 28-nm CMOS. Owing to the proposed on-chip background skew calibration, the peak tone by skew was reduced by 23 dB from -40 to -63 dB, which corresponds to the residual skew reduction from 1.6 ps to 113 fs near the Nyquist input. Thus, the prototype ADC achieved a spurious free dynamic range (SFDR) over 52.8 dB and a signal-to-noise-and-distortion ratio (SNDR) over 44.9 dB with 18.2-mW power consumption, which leads to a Walden figure-of-merit (FoM) of 57.8 fJ/conversion-step.