The main challenge for the development of a high efficiency supercapacitor is the electrode material. Developing electrode materials with high specific electrical capacitance and low electrical resistance enables an increase in the energy accumulated in the device. In addition, it is expected that the electrode material presents a simple procedure for preparation having low production cost and being environmentally friendly. This work is based on the deposition of silver nanoparticles on activated carbon felt (Ag@ACF) as a supercapacitor electrode. The samples were characterized by field emission gun scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and textural analysis. Supercapacitor behavior was evaluated by galvanostatic charge-discharge curves, cyclic voltammetry and electrochemical impedance spectroscopy using a symmetrical two-electrode Swagelok type cell, and three different aqueous solution electrolytes: 2 M H2SO4, 6 M KOH and 1 M Na2SO4. Ag@ACF presented a high specific capacitance in KOH, about 170 F g-1, which makes it an interesting material for supercapacitor electrodes and it showed good specific electrical capacitance, low resistance and high cyclability.
1 January 2012 in Journal of the Electrochemical Society
In this paper, the Cu electrodeposition on boron doped diamond (BDD) electrodes was studied. The reactions and the nucleation mechanism were evaluated by analyzing the influence of different electrolytes and Cu2+ ion concentrations in the solution. The cyclic voltammetry results showed that the Cu deposition and dissolution processes were affected by the solution pH. In acidic solutions (pH∼2.0), the energy required to initiate the nucleation process was higher than that for the Na2SO4 solution (pH∼5.0). The nucleation mechanisms were examined by fitting the experimental chronoamperometric data into appropriated nucleation models. Using the model developed by Scharifker- Hill, the Cu nucleation mechanism in 0.1 mol L−1 Cu2+ ions concentration was inconclusive – independent of the pH solution. However, the Cu nucleation mechanism was conclusive in 10−3 mol L−1 CuSO4 solutions containing Na2SO4 and H2SO4 as electrolyte. So, from (i/imax)2 vs t/tmax profile, Cu instantaneous nucleation was verified. Other more complete models of nucleation like those developed by Sharifker-Mostany (SM) and Hermann-Tarallo (HT), also confirmed the Cu instantaneous nucleation, from the Cu nuclei density (N0) determined by fitting the potentiostatic transients.
1 January 2012 in International Journal of Electrochemistry
The Cu/Pd bimetallic system electrodeposited on boron-doped diamond (BDD) films for application, as electrode material in the electrochemical reduction of nitrate was studied. The electrochemical behavior of Cu, Pd, and Cu/Pd bimetallic system was evaluated by cyclic voltammetry. From these results, the formation of the Cu/Pd composite was verified. In addition, Cu with different phases and a Cu/Pd phase in the composite were obtained. Morphological analysis by scanning electron microscopy (SEM) revealed a homogeneous distribution of Cu/Pd bimetallic particles with intermediary dimensions compared to those observed in Cu or Pd electrodeposits separately. These composites were tested as electrocatalysts for nitrate reduction in Britton-Robinson buffer solution (pH 9). Electrochemical measurements showed that composites with higher Cu content displayed the best electrocatalytic activity for nitrate reduction, and the Cu/Pd phase in the bimetallic system served to improve the Cu adherence on BDD electrode.
RESUMO Compósitos poliméricos reforçados com fibras de carbono são materiais cada vez mais utilizados em diferentes segmentos industriais, em especial, os segmentos aeronáuticos e automobilísticos devido a sua elevada resistência mecânica e baixa massa específica. Desta forma, existe grande preocupação com o descarte e a reciclagem dos componentes que representam produtos de alto valor econômico agregado, principalmente fibras de carbono. O processo de pirólise tem sido um dos métodos de reciclagem de compósitos para recuperar as fibras de carbono a partir da degradação da matriz polimérica. No setor de energia, fibras de carbono são traduzidas como bons materiais de armazenamento de energia, por apresentar desejáveis características condutoras e capacitivas que potencializam sua aplicação como material de eletrodo em supercapacitores. Neste sentido, a proposta deste trabalho consiste em viabilizar o uso de fibras de carbono recicladas por pirólise de compósitos epóxi reforçado com fibras de carbono como material de eletrodo de supercapacitores e avaliar a influência dos tratamentos termoquímico e químico sobre suas propriedades capacitivas. Imagens FEG-MEV mostraram que as fibras de carbono foram praticamente limpas permanecendo um mínimo de carbono residual sobre a superfície. A área BET e as análises FTIR, Raman e de voltametria cíclica mostraram que os tratamentos termoquímico e químico realizados na FCP não contribuíram para melhorar a capacidade de armazenamento de cargas na interface eletrodo/eletrólito, pelo contrário, o tratamento químico levou a uma grande redução da capacidade da FCP no armazenamento de energia devido a incorporação de grupos OH e COOH. As curvas de carga/descarga evidenciam boa ciclabilidade e os valores de capacitância específica para a fibra de carbono reciclada de 34 Fg-1, densidade de potência de 37,6 Wkg-1 e densidade de energia de 4,7 Whkg-1encontram-se dentro da faixa para aplicações como eletrodos de supercapacitores.