1 March 2019 in Physics in Medicine & Biology
This study presents an investigation of human skin exposure to obliquely incident electromagnetic waves at frequencies from 6 GHz to 1 THz. We aim to clarify the relationship between the power density and the skin surface temperature elevation under various exposure conditions. A Monte Carlo simulation was conducted to assess the transmittance and surface temperature elevation considering the variation of skin tissue thickness. For the case of TM wave injection, transmittance increases with increasing incidence angle from the normal incidence because of the Brewster effect. The normal incidence is confirmed as the worst-case exposure condition when the incident power density is defined in an area normal to the propagation direction. In addition, we investigated the power density required to obtain the equivalent temperature elevation over the skin surface. The analysis shows that the incident power density defined in the direction normal to the skin surface may underestimate the temperature elevation when TM waves are incident over the normal incidence up to the maximum transmittance angle. Our results also show that the power density inside the skin surface strongly correlates with the surface temperature elevation but less dependent on the frequency and independent of the oblique incidence angle and polarization. The findings of this study are expected to be valuable for discussing how to use the different definitions of power density based on dosimetric characteristics as measures in safety guidelines to protect humans from excessive temperature elevation by millimeter and submillimeter-wave exposure.
20 January 2023 in IEEE Access
International organizations have collaborated to revise standards and guidelines for human protection from exposure to electromagnetic fields. In the frequency range of 6–300 GHz, the permissible spatially averaged epithelial/absorbed power density, which is primarily derived from thermal modeling, is considered the basic restriction. However, for the averaging methods of the epithelial/absorbed power density inside human tissues, only a few groups have presented calculated results obtained using different exposure conditions and numerical methods. Because experimental validation is extremely difficult in this frequency range, this paper presents the first intercomparison study of the calculated epithelial/absorbed power density inside a human body model exposed to different frequency sources ranging from 10–90 GHz. This intercomparison aims to clarify the difference in the calculated results caused by different numerical electromagnetic methods in dosimetry analysis from 11 research groups using planar skin models. To reduce the comparison variances caused by various key parameters, computational conditions (e.g., the antenna type, dimensions, and dielectric properties of the skin models) were unified. The results indicated that the maximum relative standard deviation (RSD) of the peak spatially averaged epithelial/absorbed power densities for one- and three-layer skin models were less than 17.49% and 17.39%, respectively, when using a dipole antenna as the exposure source. For the dipole array antenna, the corresponding maximum RSD increased to 32.49% and 42.55%, respectively. Under the considered exposure scenarios, the RSD in the spatially averaged epithelial/absorbed power densities decreased from 42.55% to 16.7% when the frequency was increased from 10–90 GHz. Furthermore, the deviation from the two equations recommended by the exposure guidelines for deriving the spatially averaged epithelial/absorptive power density was mostly within 1 dB. The fair agreement in the intercomparison results demonstrates that the variances of the spatially averaged epithelial/absorbed power densities calculated using planar skin models are marginal.
9 November 2021 in IEEE Access
Recently, international exposure guidelines/standards for human protection from electromagnetic fields were revised. For frequencies between 6-300 GHz, the permissible incident power density is defined as the reference level, which is derived from a new metric “absorbed/epithelial power density” based on thermal modeling. However, only a few groups computed the power density and the resultant temperature rise at frequencies greater than 6 GHz, where their exposure conditions were different. This study presents the first intercomparison study of the incident power density and the resultant temperature rise in a human body exposed to different frequency sources ranging from 10 to 90 GHz. This intercomparison aims to clarify the main causes of numerical calculation errors in dosimetry analyses through objective comparison of computation results from six organizations using their numerical methods with various body and antenna models. The intercomparison results indicate that the maximum relative standard deviation (RSD) of peak spatially averaged incident power densities for dipole and dipole array antennas is less than 22.1% and 6.3%, respectively. The maximum RSD of the heating factor, which is defined as the ratio of the peak temperature elevation at the skin surface to the peak spatially averaged incident power density in free space, for dipole and dipole array antennas is less than 43.2% and 41.2%, respectively. The deviations in the heating factors caused by different body models and dielectric/thermal parameters are within 33.1% and 19.6% at 10 and 30 GHz, respectively, when the antenna-to-skin model distance is greater than 5 mm. Under this condition (>5 mm), the deviation in the heating factors caused by different antenna models at 30 GHz does not exceed 26.3%. The fair agreement among the intercomparison results demonstrates that numerical calculation errors of dosimetry analyses caused by the definition of spatially averaged incident power density are marginal.
11 January 2019 in IEEE Access
JCJerdvisanop Chakarothai
This study aims to clarify the accuracy of a method for assessing the power density in close proximity to a wireless communication device operating above 6 GHz for the assessment of compliance with radio-frequency exposure guidelines. We focused on a near-field reconstruction technique that estimates the power density in close proximity to a wireless communication device using the results of electric field measurement at a plane several wavelengths away from the device. In this study, the reconstruction technique was first validated by comparing the results evaluated using this technique with those obtained by computational simulation for the case of a standard horn antenna. Secondly, the reconstruction errors of the technique were assessed using ten planar array antennas at frequencies from 15 to 100 GHz. Reconstruction errors no larger than 0.35 dB were obtained for the maximum spatially averaged power density at a separation distance of over 0.15λ from the antennas using an averaging area of λ2 or larger, where λ denotes a wavelength. Finally, the requirement for electric field measurement was also examined, where the combined error for the compliance assessment of the power density was suggested for an actual testing scenario. These results support the standardization of compliance assessment techniques for wireless communication devices operating above 6 GHz, which are expected to be introduced in the near future.
31 August 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
In this brief, a novel microstrip switchable bandpass filter (BPF) is presented. By switching RF p-i-n diodes on/off, the proposed topology could provide three different filtering states: broadband bandpass filter (BBPF), dual-band bandpass filter (DBPF) and tri-band bandpass filter (TBPF). For each state, the relationship between bandwidths and return losses are newly analyzed by proposed algorithm, then the design charts can be easily summarized. In order to improve selectivity and stopband rejection, two cascaded proposed topologies are also considered and discussed briefly. For demonstration, two switchable circuits are designed, fabricated and measured in the experiment. Simulated and measured results are matched very well.
11 August 2021 in IEEE Transactions on Electromagnetic Compatibility
This article reports on an intercomparison study on the effect of the incidence angle on the spatial average of incident power density (PD) and resultant temperature rise using computational and thermographic measurement approaches. Two definitions of the spatial average of incident PD—the peak spatial-average normal component of the Poynting vector and peak spatial-average norm of the Poynting vector—were compared. First, an intercomparison of incident PD and temperature rise in a layered skin model was conducted for a 4 × 4 dipole array antenna. The variations caused by antenna type, antenna-body distance, and skin model to these definitions were then discussed. The results revealed that both definitions are in good agreement and correlate with the peak temperature rise for small or moderate incidence angles. The heating factor was enhanced for transverse-magnetic-like polarized waves for peak spatial-average normal component of the Poynting vector for large-angle incidences because of the Brewster effect. The normal incidence scenario was confirmed to be essential for considering the peak skin temperature rise.