The MADMAX project aims at detecting axion dark matter in the mass range of 100 μeV. To facilitate axion to photon conversion with detectable rate a superconducting dipole magnet with a large bore is needed. The MADMAX dipole magnet has to generate ∼9 T in a 1.35 m aperture over ∼1.3 m in length. A key challenge for a magnet made of a cable in-conduit conductor (CICC), operating at 1.8 K with an indirect bath cooling is the quench detection. In order to validate feasibility, a mock-up coil with a quench behavior scalable to MADMAX was designed and produced. The paper gives an overview of the technical details of the MACQU test coil. The conductor, the magnet, the busbar and the supporting and cryogenic systems were designed at CEA. The cable was manufactured in China at the Chang Tong INC from WST Nb-Ti strands, the insertion and compaction was achieved in the ASIPP institute with a copper profile from Aurubis. The winding of the coil and the busbar pre-forming were performed at Bilfinger Noell as well as the assembly of the supporting structure and the thermal shield. The magnet was integrated in the JT60 test station at CEA Saclay and extensively tested. The magnet current reached 80% on the loadline instead of 90% as expected at nominal. The limitation is likely coming from uneven current distribution at the extremity of the magnet at the connection box location. Nevertheless, quench tests were successfully performed at constant currents from 10 kA to 17 kA. They proved that the initial quench velocities are of the order of 1 m/s to 10 m/s, high enough to safely detect a voltage drop in MADMAX and discharge the magnet. In addition, a thermo-hydraulic quench back effect was observed in the MACQU coil cooled by superfluid helium.
15 September 2023 in IEEE Transactions on Applied Superconductivity
One of the challenges in the research of axion-like particles and ultimately in the exploration of the physics beyond the Standard Model is the high magnetic field required in large volume detectors. For the MADMAX (MAgnetized Disk and Mirror AXion) experiment, a 9 T NbTi block dipole magnet, 5.9 m in length with a bore diameter of 1.35 m, is required to detect axions with masses in the range of 100 μeV. Such large dimensions and demanding performances led to unconventional solutions for the magnet design. In this paper, the updated magnetic and mechanical design are reported. Starting from the updated physics requirements, the paper introduces the modifications adopted respect to the conceptual magnetic design and the impact of using cables-in-conduits. The magnetic and mechanical designs are described hereafter, showing the latest results in terms of optimization of the magnetic field peak, conductor cost, mechanical constraints and overall mass reduction.
15 June 2023 in IEEE Transactions on Applied Superconductivity
The MADMAX (MAgnetized Disc and Mirror AXion) project aims at detecting axion dark matter in the mass range around 100 μeV. Prerequisite for success is a very large dipole (1.35 m warm bore) with a high magnetic field up to 10 T. A first conductor design made of Nb-Ti Rutherford Cable On Conduit Conductor with a hole in the copper conduit (RCOCC type) was already presented. The coolant is static bath of superfluid helium at 1.8 K. Unfortunately, no conductor manufacturer with an available production line was found to take in charge the cable insertion/soldering process. Actually, such a production line should be compatible with large conductor section (∼400 mm²) including a solder wave device. The type of conductor was changed to use a line developed for ITER Cable In Conduit Conductor (CICC). Nevertheless, the jacket part was kept in copper. The main evolution of the MADMAX conductor design is presently reviewed. The final outer dimensions of the conductor, the void fraction and the required cold work of the copper induces a reverse engineering challenge on the initial shape of the copper profile. Then, the cable geometry modification involves a lots of differences in terms of self-field, strand diameters, transposition paths, joints technique and conductance between the strands and the stabilizer. The mechanical aspects are subject to evolution for the project due to the magnetic design optimization and conductor type change. A sub-modeling approach is used to detail the stress level in the stabilizer jacket. The possibility of wire motion and wire deformation during the conductor compaction in the production line is also discussed. Concerning the thermal analysis, the major difference is the thermo-hydraulic quench back that induces a much higher pressure drop of the helium in the conduit. So, higher pressure induced higher helium velocity and a fast detection after a quench event in superfluid environment becomes possible.
10 September 2025 in IEEE Transactions on Applied Superconductivity
MARCO is the new superconducting solenoid for ePIC, the general-purpose detector capable of delivering the full scientific scope of the Electron-Ion Collider at Brookhaven National Laboratory. This 3.84 m long solenoid, with a bore diameter of 2.84 m, will provide a magnetic field of 2.0 T at the center with a nominal current of 4 kA at 4.5 K, for a total stored energy of 45 MJ. Its conductor is a NbTi Rutherford in Copper Channel (RICC), specially designed to stand the high mechanical loads induced by the magnetic field. Its copper stabilizer will assure the protection in case of quench. The coils are wound into six layers inside a thin external mandrel in brass, with a triple role of mechanical reinforcement, cryogenic support for the thermosiphon circuit and quench-back propagator. With a cold mass average radial thickness of just 7 cm, the magnet fulfills all the criterions of transparency for the particles directed to the hadronic calorimeter forecast around the cryostat. In this paper, the design of MARCO is presented, with a specific focus on the magnetic and quench analysis.
28 August 2023 in IEEE Transactions on Applied Superconductivity
In the field of dark matter research, the MAgnetized Disk and Mirror Axion eXperiment (MADMAX) aims for the direct search of axions in a mass range around 100μeV. To have enough sensitivity on this range a dipole composed of 18 coils must reach a figure of merit of 100 T $\mathbf {^{2}}$ m $\mathbf {^{2}}$ . For this purpose, the use of a cable-in-conduit conductor (CICC) with a copper profile filled with static superfluid helium is under investigation. In order to prove the reliability of such a conductor in this magnet design as well as characterizing the quench propagation, a magnet solenoid mockup is tested within the JT60SA Cold Test Facility (CTF). To reproduce the thermal configuration of a MADMAX coil, the solenoid mockup is cooled down at 1.8 K directly through the void section of the CICC by pressurised superfluid helium and the mandrel, by conduction, without being immersed in a helium bath. The long distance to the heat exchanger coupled with the narrow helium section in the CICC limits the Gorter-Mellink heat transport, thus the cool down efficiency and heat losses must be tackled. This paper describes the thermal design of the experimental facility, the explanation of a thermal model for superfluid helium cool down and operation and the first experimental results.