7 December 2017 in IEEE Transactions on Electron Devices
To combat the large variability problem in resistive random access memory, current compliance elements are commonly used to limit the in-rush current during the forming operation. Regardless of the compliance element (1R-1R or 1T-1R), some degree of current overshoot is unavoidable. The peak value of the overshoot current is often used as a predictive metric of the filament characteristics and is linked to the parasitic capacitance of the test structure. The reported detrimental effects of higher parasitic capacitance seem to support this concept. However, this understanding is inconsistent with the recent successes of compliance-free ultrashort pulse forming which guarantees a maximum peak overshoot current. We use detailed circuit analysis and experimental measurements of 1R-1R and 1T-1R structures to show that the peak overshoot is independent of the parasitic capacitance while the overshoot duration is strongly dependent on the parasitic capacitance. Forming control can be achieved, in ultrashort pulse forming, since the overshoot duration is always less than the applied pulse duration. The demonstrated success of ultrashort pulse forming becomes easier to reconcile after identifying the importance of overshoot duration.
2 May 2017 in IEEE Electron Device Letters
The stochastic nature of the conductive filaments in oxide-based resistive memory resistive random access memory (RRAM) represents a sizeable impediment to commercialization. As such, program-verify methodologies are highly alluring. However, it was recently shown that the program-verify methods are unworkable due to strong resistance state relaxation after SET/RESET programming. In this letter, we demonstrate that resistance state relaxation is not the main culprit. Instead, it is fluctuation-induced false-reading (triggering) that defeats the program-verify method, producing a large distribution tail immediately after programming. The fluctuation impact on the verify mechanism has serious implications on the overall write/erase speed of RRAM.
23 January 2017 in IEEE Electron Device Letters
We report on new fluctuation dynamics of the high resistance state of Hafnia-based RRAM devices after RESET. We observe that large amplitude fluctuations occur more frequently immediately after programming and their frequency of occurrence decays in the tens of microseconds. The fluctuation amplitude, on the other hand, does not decay noticeably over the entire millisecond read time. While post-programming instability and post-programming resistance dispersion have both been reported in the literature, the relaxation in the frequency of occurrence without a commensurate amplitude decay is new. Since picosecond pulses were used for our RESET operation, post-programming thermalization occurs on the nanosecond time scale. This clearly eliminates a thermally driven mechanism as the cause of the observed fluctuation behavior. Furthermore, reducing the READ voltage by tenfold does not have any effect and also eliminates read disturb as possible cause.
29 March 2018 in IEEE Transactions on Nuclear Science
We observe a gamma-irradiation-induced change in electrically detected magnetic resonance (EDMR) in TiN/Ti/HfO 2 /TiN resistive random access memory (RRAM). EDMR measurements exclusively detect electrically active defects, which are directly involved in the transport mechanisms within these devices. The EDMR response has an isotropic g value of 2.001 ± 0.0003. The response increases dramatically with increased gamma irradiation. We tentatively associate this EDMR response with spin-dependent trap-assisted tunneling events at O 2 - centers coupled to hafnium ions. Although our study cannot fully identify the role of these defects in electronic transport, the study does unambiguously identify changes in transport defects caused by the ionizing radiation on defects involved in electronic transport in RRAM devices. This paper also contributes more broadly to the RRAM field by providing direct, though incomplete, information about atomic scale defects involved in electronic transport in leading RRAM systems.
30 August 2016 in IEEE Transactions on Electron Devices
We report a new technique for the rapid measurement of full capacitance-voltage (C-V) characteristic curves. The displacement current from a 100-MHz applied sine wave, which swings from accumulation to strong inversion, is digitized directly using an oscilloscope from the MOS capacitor under test. A C-V curve can be constructed directly from this data but is severely distorted due to nonideal behavior of real measurement systems. The key advance of this paper is to extract the system response function using the same measurement setup and a known MOS capacitor. The system response correction to the measured C-V curve of the unknown MOS capacitor can then be done by simple deconvolution. No deskewing and/or leakage current correction is necessary, making it a very simple and quick measurement. Excellent agreement between the new fast C-V method and C-V measured conventionally by an LCR meter is achieved. The total time required for measurement and analysis is approximately 2 s, which is limited by our equipment.
7 March 2017 in IEEE Transactions on Electron Devices
Most experimental reports of tunneling field-effect transistors show defect-related performance degradation. Charging of oxide traps causes Fermi-level pinning, and Shockley-Read-Hall (SRH)/trap-assisted tunneling (TAT) cause unwanted leakage current. In this paper, we study these degradation mechanisms using the pulsed I-V technique. Our simulations show pulsed I-V can fully suppress oxide trap charging, unlike SRH and TAT. We discuss several circuit-related pitfalls, and we demonstrate improved transfer characteristics by suppressing oxide trap charging using cryogenic pulsed I-V.