Centro Peruano Japonés de Investigaciones Sísmicas y Mitigación de Desastres, Facultad de Ingeniería Civil, Universidad Nacional de Ingeniería, 1150 Av. Tupac Amaru, Rimac, Lima 15333, Peru
Auto-generated profile, based on publicly available information
Fernando Lazares
Centro Peruano Japonés de Investigaciones Sísmicas y Mitigación de Desastres, Facultad de Ingeniería Civil, Universidad Nacional de Ingeniería, 1150 Av. Tupac Amaru, Rimac, Lima 15333, Peru
The location of Lima city and El Callao in the Pacific coast and the long history of seismic activity were the main reasons to develop a seismic microzoning map. The microzoning study was based on large numbers of geotechnical and geophysical exploration points distributed around the study area. The geotechnical exploration consisted of borehole tests and pits, from which soil samples were taken to the laboratory to determine the soil mechanical characteristics. The geophysical exploration consisted of onepoint microtremor measurements and various methods to estimate the S-wave velocity profile. The results of both, the geotechnical and geophysical exploration were combined to develop a seismic microzoning map for Lima city and El Callao. This map shows five zones, where the zone with the best soil mechanical and dynamic characteristics covers most of the study area.
In order to create a soil amplification map for Lima, Peru, parameters that correlate best with amplification are examined. Shallow shear wave velocity profiles estimated from MASW measurements at 105 sites were used to provide amplification factorAvTF.AVs10seems to be the best value for estimating amplification in Lima from the data available. We have attempted to createAVs10map correlating three parameters – elevation, H/V peak period, and soil type. From thisAVs10map, we have estimated an amplification map for Lima.
Microtremor exploration was performed around seismic recording stations at five sites in Lima city, Peru in order to know the site amplification at these sites. The Spatial Autocorrelation (SPAC) method was applied to determine the observed phase velocity dispersion curve, which was subsequently inverted in order to estimate the 1-D S-wave velocity structure. From these results, the theoretical amplification factor was calculated to evaluate the site effect at each site. S-wave velocity profiles at alluvial gravel sites have S-wave velocities ranging from ∼500 to ∼1500 m/s which gradually increase with depth, while Vs profiles at sites located on fine alluvial material such as sand and silt have Swave velocities that vary between ∼200 and ∼500 m/s. The site responses of all Vs profiles show relatively high amplification levels at frequencies larger than 3 Hz. The average transfer function was calculated to make a comparison with values within the existing amplification map of Lima city. These calculations agreed with the proposed site amplification ranges.
In seismic design, intensity parameters that represent seismic demand are commonly used. A probabilistic seismic hazard assessment is an accurate way of assessing seismic demand, based on a set of parameters that represent the seismicity of a region. However, because some regions lack sufficient information, the selection of these parameters can be controversial. In Peru, selecting a maximum earthquake magnitude (Mmax) for regional seismic hazard assessments has proven to be a challenging task due to the limited available information concerning of large-magnitude events. This study evaluated the Mmax for subduction earthquakes using scaling relationships, empirical evidence, and the extreme value statistics (Kijko and Bayesian) approach. The seismic catalog was updated to February 2022 and divided into 19 subduction seismic sources (5 interface and 14 intraslab). The results showed that the obtained Mmax are within the range of Mw 8.7–9.0 for the interface and Mw 7.6–8.1 for the intraslab sources, which unlike the Mmax values established in previous regional seismic hazard assessments, are more consistent with the historical and instrumental seismicity and rupture models.
Evaluation of site amplification factors (SAFs) of seismic waves has been one of the important issues for evaluating seismic hazards. The authors have proposed a deep neural network (DNN) model in order to cost-effectively and accurately estimate SAF from microtremor horizontal-to-vertical spectral ratio (MHVR). In this study, we assessed the SAFs in southern Lima, Peru by estimating from MHVRs and DNN. First, we validated the applicability of the DNN model to Lima by estimating the SAFs from the MHVRs observed at seismic stations in Lima. From the comparison with the observed SAFs derived from spectral inversion technique, we confirmed that the SAFs in Lima were accurately estimated by the DNN model. The SAFs in the southern Lima including Chorrillos and Villa El Salvador districts were evaluated by applying the DNN model to the observed MHVRs at approximately 250 sites. We found that large amplifications at low frequency around 1 Hz were expected in the southeastern coastal areas formed by eolian sands whereas smaller amplification were estimated in the northwestern areas mainly located on alluvial deposits.