Centro Peruano Japonés de Investigaciones Sísmicas y Mitigación de Desastres, Facultad de Ingeniería Civil, Universidad Nacional de Ingeniería, Lima, Perú
Auto-generated profile, based on publicly available information
Juan Carlos Tarazona
Centro Peruano Japonés de Investigaciones Sísmicas y Mitigación de Desastres, Facultad de Ingeniería Civil, Universidad Nacional de Ingeniería, Lima, Perú
In seismic design, intensity parameters that represent seismic demand are commonly used. A probabilistic seismic hazard assessment is an accurate way of assessing seismic demand, based on a set of parameters that represent the seismicity of a region. However, because some regions lack sufficient information, the selection of these parameters can be controversial. In Peru, selecting a maximum earthquake magnitude (Mmax) for regional seismic hazard assessments has proven to be a challenging task due to the limited available information concerning of large-magnitude events. This study evaluated the Mmax for subduction earthquakes using scaling relationships, empirical evidence, and the extreme value statistics (Kijko and Bayesian) approach. The seismic catalog was updated to February 2022 and divided into 19 subduction seismic sources (5 interface and 14 intraslab). The results showed that the obtained Mmax are within the range of Mw 8.7–9.0 for the interface and Mw 7.6–8.1 for the intraslab sources, which unlike the Mmax values established in previous regional seismic hazard assessments, are more consistent with the historical and instrumental seismicity and rupture models.
Early damage estimation in the immediate aftermath of a catastrophic earthquake is critical for effective disaster response and informed decision-making, especially in densely populated urban areas with high seismic activity, such as the Lima Metropolitan Area, Peru. This research focuses on designing and developing a web-based geographic information system for early earthquake damage estimation, featuring a four-stage workflow. Stage 0 generates pre-event damage estimations using earthquake scenarios, infrastructure datasets, and vulnerability models. Stage 1, initiated immediately after an earthquake, selects the closest pre-calculated scenario by comparing the peak ground acceleration values recorded by accelerometers with pre-estimated intensity measures. Stage 2 creates ShakeMaps by interpolating observed ground motion indices to produce the updated damage estimates based on real-time intensity distributions. A future Stage 3 will refine these estimates using post-event observed data. Data acquisition relies on open geospatial services and Peruvian governmental platforms, integrating datasets related to general buildings, essential buildings (schools and hospitals), transportation networks (bridges and roads), and lifeline systems (water supply and sewage). The system was implemented using open-source geospatial tools, providing a cost-effective, scalable solution for early-time disaster management in earthquake regions.
The seismic response evaluation of soil deposits in Metropolitan Lima requires analysis methods that can capture local amplification effects, owing to the region’s complex alluvial stratigraphy and high seismicity. This study performs a comparative assessment of four site response analysis methods using records from the 2021 Mala (M w 6.0) earthquake, located south of Lima: (1) normative amplification factors (NAF E.030), (2) ground motion models (GMM), (3) average amplification factors (AAF), and (4) one-dimensional wave propagation analysis (1DPA). Performance was evaluated using root mean square error (RMSE) between observed and predicted response spectra as the primary accuracy metric. A total of 31 accelerographic stations were analyzed, classified by time-averaged shear wave velocity of the top 30 m soil layers (V s 30) into three categories: stiff (S1’: 550–800 m/s), intermediate (S2 ′ : 350–550 m/s), and soft (S3’: 200–350 m/s) soils. Linear elastic soil behavior was confirmed through 1DPA, indicating maximum shear strains below 0.01% across all sites, well within the elastic threshold. The results revealed that 1DPA analysis produced the most accurate estimates, with average RMSE values of 27.4 cm/s 2 for S1’ soils and 38.5 cm/s 2 for S2’ soils. NAF E.030 performed well in 8 out of 10 stiff soil sites (RMSE =33.1 cm/s 2 ), however, exhibited significant limitations in softer soils where RMSE values exceeded 37 cm/s 2 . GMM and AAF methods demonstrated RMSE values ranging from 44.8 to 51.4 cm/s 2 , with reduced accuracy in long-period ranges (>1.0 s) and S3’ soil sites. These findings highlight the need to revise current normative amplification factors for soft soils and support the implementation of 1DPA analysis in areas with complex stratigraphy or deep sedimentary deposits, thereby contributing to improved seismic-resistant design practices in Metropolitan Lima.