13 April 2015 in The Journal of Physical Chemistry C
1 November 2011 in Journal of the Mechanical Behavior of Biomedical Materials
22 March 2010 in Advanced Functional Materials
27 June 2011 in ACS Applied Materials & Interfaces
Nanocrystalline (nc) Ni films show pronounced grain growth and suffer from concomitant deterioration of their mechanical and magnetic properties after annealing at relatively low temperatures (TANN ≥ 475 K). This constitutes a drawback for their applicability as coatings or in components of miniaturized devices. This work reveals that the thermal stability of nc Ni is significantly improved by controllably alloying Ni with Cu, by means of electrodeposition, to form a Ni1–xCux solid solution. To tune the composition of such nc alloys, Ni1–xCux films are deposited galvanostatically using an electrolytic bath containing Ni and Cu sulfate salts as electroactive species, saccharine as grain-refining agent, and applying current densities ranging from −10 to −40 mA cm–2. The enhanced thermal stability is ascribed to segregation of a Cu-rich phase at the Ni1–xCux grain boundaries, which acts as a shielding layer against grain growth. As a result, high values of hardness (in excess of 6 GPa) remain in nc Ni1–xCux for x ≥ 0.3, even after annealing at TANN ≥ 575 K. From a magnetic point of view, Ni1–xCux films possess lower coercivity values than pure nc Ni films, both in the as-prepared and annealed states, thus offering potential advantages for certain soft magnetic applications.
1 September 2011 in Surface and Coatings Technology
This is the author’s version of a work that was accepted for publication in Surface & coating technology. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Surface & coating technology, Vol. 205, Núm. 23-24 (Sep 2011), p. 2585-5293 DOI 10.1016/j.surfcoat.2011.05.047Cu1−x–Nix (0.43 ≤ x ≤ 1.0) films were electrodeposited from citrate–sulphate baths at different current densities onto Cu/Ti/Si (100) substrates with the addition of saccharine as a grain-refining agent. The Cu–Ni alloy films produced from saccharine-free baths were fine-grained (crystallite size of ~400 nm). The addition of saccharine to the electrolytic solution induced a dramatic decrease in crystal size (down to ~27 nm) along with a reduction in surface roughness. Although the effect of saccharine on pure Ni films was less obvious, significant changes were observed due to the presence of saccharine in the bath during the alloying of Cu with Ni. Compared to fine-grained Cu–Ni films, the nanocrystalline films exhibited lower microstrains and a larger amount of stacking faults as observed by X-ray diffraction. These features enhance the mechanical properties of the Cu–Ni alloys, making the nanocrystalline Cu–Ni films superior to both the corresponding fine-grained films and pure Ni films. In particular, hardness in fine-grained films varied from 4.2 (x=0.43) to 5.4 GPa (x=0.86), whereas hardness varied between 6.7 and 8.2 GPa for nanocrystalline films of similar composition. In addition, wear resistance and elastic recovery were enhanced. Nanostructuring did not significantly affect corrosion resistance of Cu–Ni alloys in chloride media. Although the corrosion potential shifted slightly towards more negative values, the corrosion current density decreased, thereby making the electrodeposition nanostructuring process an effective tool to improve the overall properties of the Cu–Ni system
1 August 2015 in Electrochimica Acta
Altres ajuts: M. Guerrero acknowledges the support of the Secretary for Universities and Research of the Government of Catalonia and the COFUND Programme of the Marie Curie Actions of the 7th R&D Framework Programme of the European Union for the ‘Beatriu de Pinos’ contract (2013 BP-B 00077). M. D. Baró acknowledges partial financial support from an ICREA-Academia Award.1.5 μm-thick molybdenum oxide films have been electrodeposited potentiostatically from 0.2 M Na₂MoO₄ electrolyte onto indium tin oxide (ITO)/glass substrates at pH = 1, 6 and 9. The influence of cetyltrimethylammonium bromide (CTAB) surfactant on films' adhesion, morphology, degree of porosity, molybdenum speciation, and crystallographic structure has been systematically investigated. The addition of CTAB (0.01 M) to the bath clearly improves film adherence to the substrate, reduces cracking, and increases crystallinity. This has an impact on the physical properties of the films. In particular, both hardness (H) and Young's modulus (E) increase, as determined from nanoindentation tests. The growth of ordered arrays of molybdenum oxide submicrometer structures, including pillars and stripes, by electrodeposition onto e-beam lithographed Au/Ti/Si substrates is also reported