1 November 2015 in IET Science, Measurement & Technology
This study deals with the analysis of the leakage current (LC) in both time and frequency domains, for different configurations of polluted high voltage insulators (i.e. for clean and polluted insulator surfaces). The characteristic parameters of the recorded LC waveforms up to flashover namely the peak value, the phase shift, the total harmonic distortion and the harmonic contents are investigated. It is shown that the LC peak value and the phase shift cannot be a trustworthy indication of the surface activity related to partial discharges and waveform type whereas the harmonic components magnitude can be well correlated with the LC distortions; it is shown that in the early stages, the fifth and seventh harmonics contribute to the distortion of the LC whereas for advanced stage, the third harmonic contribution is the most significant. A time–frequency analysis is also carried out to better understand the LC behaviour. The spectrogram of the different stages of LC activity is computed using Matlab toolbox. The results show that time–frequency analysis can be used as a tool for patterns recognition and classification of the LC.
28 June 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
This article is aimed at the investigation of the electrical potential and field distributions along an insulating system covered/coated with a thin semi-conductive layer usually found on outdoor insulator surface or used on the end-windings of rotating machines and high voltage (HV) terminations. For that purpose, a model is proposed to compute analytically the electrical potential and field distributions along the insulator surface. The peculiarity of this model is that it considers both conduction and displacement currents within the thin semi-conductive layer. The results of this new model are compared with those reported in the literature and those obtained by numerical methods such as the collocation spectral method (CSM), finite difference method (FDM), and finite element method (FEM). The influence of the thin semi-conductive layer parameters is discussed in linear and nonlinear cases to show the advantage of the use of a semi-conductive thin layer as a coating stress grading material in HV equipment.
3 February 2025 in IEEE Transactions on Dielectrics and Electrical Insulation
HV insulation systems under AC or DC are subject to partial discharges (PD) phenomena which happen randomly and can lead to progressive damage of the dielectric material and/or the outage of the line in which they occur. In order to automate the predictive maintenance, these discharges must be monitored in real time to recognize their energetic nature: low-energy (LE) ones which extinguish by themselves, or contrarily high-energy (HE) ones which can lead to flashovers that imply line outage. One has then to focus on high-energy discharges since they constitute the major risk for the insulation systems and the network stability. For this aim, an experimental investigation was performed for HVDC voltages applied to composite insulators, from levels corresponding to low energy partial discharges to flashover occurrence. Thereby, low noise nanosecond scale measurements are taken simultaneously for voltages, currents and radiated magnetic fields by both types of discharge where a qualitative database was obtained. This paper presents the use of efficient and fast feature selection software that uses the Fisher score as evaluation criterion. The features are selected, and then classified from the most to the least discriminant. The number of the most successive discriminant features which correspond to the best high-energy discharges recognition ratio is then searched. The obtained results from the achieved algorithm, combined with SVM, allow an important reduction of feature number from 25000 to only 37, and an improvement of 4.9% of high-energy discharges recognition when compared to the results obtained before feature selection. The approach is suitable for real time diagnosis of insulator chains close to substations and power plants.
29 May 2023 in IEEE Transactions on Dielectrics and Electrical Insulation
This paper presents a new numerical computation code based on the Collocation Spectral Method (CSM) to solve the partial differential equation describing the potential distribution along a polluted insulator. The pollution on insulator surface is modeled by a uniform thin layer. The results of the electric potential distribution obtained by CSM are compared with those of the Finite Difference Method, the Finite Element Method and the analytical solution. The accuracy of this method in terms of maximum (error) is discussed. Based on the newly developed code, the influence of physical parameters of the insulator model, such as the relative permittivity, surface conductivity and insulator thickness on the electric potential distribution are investigated.
1 January 2026 in IEEE Transactions on Dielectrics and Electrical Insulation
30 June 2025 in EPJ Web of Conferences
In this study, the electric potential distribution along an insulator model coated with a thin stress grading material was analyzed using a numerical formulation based on the Spectral Collocation Method (CSM). Comparative assessments against analytical solutions, established numerical approaches from the literature, and the Finite Difference Method (FDM) validated the accuracy and robustness of the proposed method. The CSM demonstrated numerical precision equivalent to that of FDM while offering significant advantages in terms of computational efficiency and implementation simplicity when compared to both FDM and the Finite Element Method (FEM). Moreover, the evaluation of the maximum electric field reduction at the high-voltage electrode quantitatively highlighted the effectiveness of incorporating nonlinear conductivity within the grading layer.