The aim of this paper is to evaluate the influence of small variations in chemical composition on the corrosion resistance and mechanical properties of low-manganese and medium manganese high strength steels. Six different steels with manganese content varying from 1.5 to 4.0 wt.% and aluminium from 0.008 to 6.5 wt.% were subjected to the analysis. The other subjects for evaluation included the effect of aluminium as a replacement for silicon, niobium microalloying and the effect of heat treatment. The effect of non-metallic inclusions on localized corrosion initiation and propagation was also documented. Using potentiodynamic testing, exposure testing, tensile and impact testing, it was found that the improvement in corrosion resistance associated with increasing aluminium content is accompanied by a significant deterioration of the mechanical properties. Niobium microalloying and heat treatment was found to have no quantifiable impact on the anti-corrosion properties. The effect of aluminium content proved to be superior to the effect of nonmetallic inclusions in terms of determining the overall corrosion resistance of the experimental steels.
Joining additively manufactured (AM) complex shaped parts to larger conventionally produced parts can lead to innovative product designs. Another alternative is direct deposition on a conventional semi-product. Therefore, similar joints of maraging tool steel 1.2709 were produced by AM deposition of powder of this steel on a bulk conventionally manufactured steel part. The resulting hybrid parts were solution annealed and precipitation hardened. Solution annealing at 820 °C for 20 min was followed by furnace cooling. Precipitation hardening was performed at 490 °C for 6 h. The mechanical properties of the samples were characterised using tensile testing and hardness measurement across the joint. Metallographic analysis was also carried out. The tensile properties of the AM and conventionally produced steel after equivalent heat treatments were also determined as the reference values. The mechanical properties of the hybrid parts are close to the properties of both steels. The hybrid parts in the as-built condition had a tensile strength of 1029 MPa and a total elongation of 14%. Solution annealing did not change these properties significantly, except for yield strength, which decreased by approximately 150 MPa. After precipitation annealing, the strength was higher, 2011 MPa, and total elongation dropped to 5%.
16 September 2023 in Journal of Materials Research and Technology
Two oxide precipitation hardened (OPH) Fe-Al-O-based steels were prepared by mechanical alloying. In addition to the variant using yttria nano-precipitates to improve the mechanical properties, a variant using only alumina precipitates for strengthening was also prepared. Therefore, a more economically acceptable variant of these steels was developed. Hot consolidation is a significant production step for achieving the required mechanical properties. Hot consolidation was performed by either hot rolling or forging. The heat treatment was subsequently performed on both variants (0.85Fe–0.11Al–0.03Y2O3–0.01Y and 0.87Fe–0.11Al–0.02O2) of the alloys to support secondary recrystallization. The paper describes the influence of the consolidation method on grain size, material recrystallization, and mechanical properties. The difference in the consolidation method was reflected in the grain size after the heat treatment, where the material consolidated by hot rolling reached a grain size of almost 200 μm, while after forging the maximum grain size was around 30 μm. A higher ultimate tensile strength was achieved with forged states, both with and without the heat treatment.
4 July 2022 in Archives of Civil and Mechanical Engineering
One approach to producing hybrid bimetallic parts is to additively manufacture a new material onto a conventionally manufactured base material. This technique can expand the potential applications of additive manufacturing and offer new solutions for the engineering design of hybrid parts. In this work, laser powder bed fusion was used to deposit MS1 maraging steel on a conventionally produced (cast and hot-rolled) 42SiCr martensitic steel base material. Despite the profoundly different chemical compositions and hardening behaviours of these materials, their yield and ultimate tensile strengths in solution-annealed and hardened conditions are quite similar. Various heat treatments were performed to optimise the mechanical properties of the resulting hybrid part. The highest yield strength of 1400 MPa and tensile strength of 1483 MPa was achieved with a post-processing heat treatment which consisted of annealing at 900 °C for 25 min followed by water quenching and subsequent very short tempering at 490 °C. In the tensile tests, all the hybrid parts, regardless of heat treatment parameters, fractured within the base material and neither in the joint nor in the adjacent heat-affected zone. The interface areas and the microstructures of both materials were documented in detail in the as-built state and also after the heat treatment.