3 May 2022 in IEEE Transactions on Power Electronics
This article addresses high-frequency admittance modeling of current-controlled voltage source converters (VSCs). Recent studies have shown that harmonic instability may also occur at frequencies above the Nyquist frequency. To form an accurate multiple-frequency model in this frequency range, sidebands that originate from modulation and sampling must be examined. In this article, an accurate small-signal model is developed taking into account an adequate digital pulsewidth modulator (DPWM) representation, which allows to predict dependence of the frequency response on the steady-state dc (SS-dc) operating point. It is shown that when center-pulse sampling is implemented, pulsewidth modulation sidebands do not create additional loops leaving only sampling sidebands to be considered. Using the same approach as for SS-dc operation, a model that accurately represents admittance measurements during sinusoidal ac (S-ac) operation is developed. Its basis is a novel DPWM model suitable for S-ac regime, which allows to predict dependence of the VSC’s input admittance on the grid voltage magnitude. Experimental and simulated admittance measurements, performed on a single-phase two-level VSC during various SS-dc and S-ac regimes, match with the proposed models up to twice the sampling frequency.
7 November 2022 in IEEE Transactions on Power Electronics
In this article, small-signal modeling of digital pulsewidth modulators (DPWMs) used in multicell voltage source converters (VSCs) is addressed. In addition to sampling and computation, DPWM introduces delay, which impairs VSC's dynamic performance and robustness. In order to take into account the influence of modulation delay, an accurate small-signal representation of DPWM is necessary. Here, modeling of multisampled bipolar and unipolar phase-shifted DPWMs for single-, double-, and multi-update strategies is presented. The simplest multilevel modulation of single-cell full-bridge VSCs, unipolar DPWM, is also covered by the analysis. The derived operating-point-dependent small-signal DPWM models are verified using simulated and experimental frequency response measurements up to four times the Nyquist frequency. Comparisons are also made with the models conventionally considered in the literature. Additionally, an approximate method is presented to model the influence of dead time on DPWM's small-signal dynamics. For the purposes of showcasing the importance of the proposed DPWM models, high-frequency admittance of a VSC employing multisampled multiupdate unipolar DPWM is modeled and verified in simulations and experiments.
22 September 2023 in IEEE Transactions on Power Electronics
This article addresses switching noise propagation and its suppression in current-controlled systems with multisampled pulsewidth modulation (MS-PWM). MS-PWM enables very high control bandwidths by reducing digital delays. However, when the sampling instants occur near the commutation ones, system performance is prone to being impaired by switching noise. It is analyzed how using the typically considered moving average filters (MAFs) in feedback may have an adverse effect, especially when the number of the noise-corrupted samples is high compared with the number of averaged samples. It is also shown that, without any filters, MS-PWM on its own may mask the negative impact of noise, due to modulator-related nonlinear effects. However, these nonlinearities can lead to an undesirable response to transients and output waveform distortion. Hence, this article proposes MS-PWM with median-based feedback filtering. To avoid ranking within median filter (MED) being affected by the switching ripple, repetitive ripple removal (RRR) is added before MED. The effectiveness of the proposed strategy in suppressing the switching noise is verified in simulations and experiments, during dc and ac operations. RRR+MED successfully suppresses noise-sensitive operating point regions that appear with MAF. Finally, it is shown that, even with added RRR+MED, MS-PWM still retains dynamic improvements over the standard DS-PWM without any filters, offering better reference tracking and disturbance rejection.
20 May 2024 in IEEE Transactions on Power Electronics
This article presents a formal mathematical correlation between the standardly used port-level (terminated) single-input single-output (SISO), and the recently acknowledged device-level (unterminated) multiple-input multiple-output (MIMO) impedance-based method for the stability assessment of dc–dc interlinking converters. Based on this, the conditions that must be met to ensure the correct stability assessment by the SISO method applied to a single port-pair are derived. It is shown that without prior knowledge on whether these conditions are met, the SISO method must be applied to every port-pair to account for possible port-level hidden dynamics . Alternatively, the MIMO method can be used, which is revealed to inherently account for any port-level hidden dynamics . It is further analyzed which method is advantageous in terms of computational complexity, intuitiveness, and simplicity for applications featuring meshed grids or multiport interlinking converters, as well as in terms of interpreting the resulting stability margins. Finally, suitability of the MIMO method for termination-independent stability-oriented controller design and stability assessment based on measurements is highlighted. The presented methodology is illustrated for a simplified dc system with a current-controlled buck converter. Analytical stability predictions are validated using hardware-in-the-loop simulations and also experimentally, using a laboratory hardware prototype.
10 November 2022 in IEEE Open Journal of Power Electronics
Small-signal stability and dynamic interactions among power electronic converters (PECs) and electrical grids are widely analyzed using the impedance-based approach. To reduce such interactions, a desirable feature of PECs is that their admittance exhibits dissipative behavior. Due to control delays, the PEC admittance usually exhibits non-dissipative zones around and above the crossover frequency of the inner control loop, possibly reducing the stability margins of the contemporary electrical grids. This paper proposes the double-sampling asymmetric dual-edge digital pulse-width modulator (ADE-DPWM) as an effective way to improve the passivity properties of the PEC admittance. Even in the digital implementation, the ADE-DPWM features zero delay and almost unity magnitude up to half of the switching frequency. Moreover, this paper examines the influence of ADE-DPWM on the PEC admittance even at higher frequencies, where destabilization of poorly damped grid resonances may be influenced by sampling and pulse-width modulation sidebands. Due to an operating point dependent ADE-DPWM small-signal model, the high-frequency passivity properties highly depend on the steady-state operating point. The analytical predictions are shown to be in excellent agreement with the experimental admittance measurements up to twice the switching frequency for all tested steady-state operating points.
9 June 2023 in IEEE Transactions on Power Electronics
This paper derives models for stationary noise propagation in multi-sampled control systems, taking decimation into account. It is explained how the decimation is either included deliberately, in case of multi-rate control, or inherently by the modulator, in case of multi-sampled pulsewidth modulation (MS-PWM). In the latter case, the decimation rate is determined by the switching frequency and the number of PWM carriers. The proposed models are then used for digital filter design, with a goal of suppressing the decimation-related aliasing and attenuating noise, while considering the imposed impact on the dynamic response. The theory is verified in simulations and experimentally, confirming the assumed decimation mechanisms as well as the potentiality of MS-PWM to jointly enable high-bandwidth control and strong noise suppression. The experimental measurements are conducted on two hardware prototypes, comprising two-level and three-level dc-dc buck converters.