Svetlana Ivanov

Svetlana Ivanov

Auto-generated profile, based on publicly available information

Svetlana Ivanov

University of Belgrade, Technical Faculty in Bor

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2023 in Revista de Metalurgia
Verified
Journal Article
Open access
PDF file
USUroš Stamenković
Uroš Stamenković
SISvetlana Ivanov
Svetlana Ivanov
IMIvana Marković
Ivana Marković
Milan GorgievskiMilan Gorgievski
Milan Gorgievski
KBKristina Božinović
Kristina Božinović
AKAvram Kovačević
Avram Kovačević
The influence of the ageing temperature on the hardness, electrical conductivity, thermal diffusivity and thermal conductivity of the EN AW-7075 aluminium alloy was studied in this paper. After solution treating the alloy at 480 °C for 1 h and quenching it in ice water, the investigated alloy was characterized using Differential Thermal Analysis (DTA) in order to determine the optimal temperatures for the isochronal ageing treatments. Afterwards, isochronal ageing was conducted at the temperature range of 110 °C-250 °C for 30 min The hardness, electrical conductivity, thermal diffusivity, thermal conductivity and microstructural features were investigated during the ageing treatments. Hardness had a peak value after ageing at 150 °C, while other properties gradually increased with the ageing temperature. Microstructural investigation of the aged alloy by SEM-EDS revealed the existence of precipitated phases that appear homogenously distributed in the microstructure.

30 December 2019 in Revista de Metalurgia
Verified
Journal Article
Open access
PDF file
USUroš Stamenković
Uroš Stamenković
SISvetlana Ivanov
Svetlana Ivanov
IMIvana Marković
Ivana Marković
LBLjubisa (Tomislav) Balanovic
Ljubisa (Tomislav) Balanovic
Milan GorgievskiMilan Gorgievski
Milan Gorgievski
En este trabajo se estudia el efecto de la precipitación de fases metaestables sobre las propiedades termofísicas y mecánicas de la aleación EN AW-6082. Después del tratamiento con solución sólida y el enfriamiento rápido en agua helada, las muestras se sometieron a análisis DSC e investigación térmica con el objetivo de definir temperaturas óptimas para el recocido isocrónico. El recocido isocrónico se realizó a temperaturas que oscilan entre 160-330 °C durante dos tiempos de recocido: 30 y 60 min. La conductividad eléctrica, la dureza, la microdureza y las propiedades estructurales se investigaron durante el tratamiento de envejecimiento isocrónico. Las propiedades mecánicas alcanzaron valores máximos durante el envejecimiento a 230 °C durante 30 min y a 220 °C durante 60 min, respectivamente. La conductividad eléctrica aumentó gra-dualmente con un aumento en la temperatura de envejecimiento debido a la precipitación de la solución sólida. Las investigaciones microestructurales realizadas por SEM-EDS confirmaron la existencia de fases precipitadas y su distribución en todas las muestras investigadas.

1 January 2021 in Hemijska industrija
Verified
Journal Article
Open access
PDF file
JPJasmina Lj. Petrović
Jasmina Lj. Petrović
SMSrba A. Mladenović
Srba A. Mladenović
AIALEKSANDRA IVANOVIC
ALEKSANDRA IVANOVIC
IMIvana I. Marković
Ivana I. Marković
SISvetlana Lj. Ivanov
Svetlana Lj. Ivanov
In this work, the stir casting method was applied to obtain composites based on the alloy AN EW 6061 used as a metal base, and Al2O3 particles as a reinforcement. Composites play a significant role as engineering materials. Therefore, it is necessary to study, in detail, the production methods and the factors that affect their mechanical properties. For this purpose, we have carried out a planned experiment wi ASM International th the aim to use regression analysis to predict the influence of particle size and mass fraction on hardness of the obtained composites. The full factorial experimental design with two factors was used, which was analyzed at three levels. Hardness was observed as a system response, while particle size and mass fraction were set as influencing factors. Influencing factors were observed at three levels: 50, 80 and 110 ?m for the particle size and 2, 5 and 8 mass%. Measured hardness values of the composites ranged from 72 HV10 to 80 HV10. Based on the probability values (p<0.05), it was determined which factors are important for the system response. Statistical analysis has shown that linear terms of the influence factors (size and mass fraction of reinforcement particles) and the square term of the mass fraction have statistical significance on the hardness change. The square term of the particle size and the interaction term of the influencing parameters do not have a statistically significant contribution in predicting the hardness value. Thus, a second-order polynomial model was obtained by the regression analysis. Influence of input factors on the system response and the adequacy of the obtained mathematical model were determined by using the Analysis of Variance (ANOVA). Based on the statistical data analysis, it was established that, the particle mass fraction has a greater influence on hardness of the obtained composite in relation to the particle size. By comparing the experimental and predicted values, a high degree of agreement was achieved so that the chosen model of the factorial experiment was adequate (R2=0.989). It can be also concluded that the developed regression model can be applied to predict hardness of the aluminum composite reinforced by Al2O3 particles in the chosen variation interval of particle size and mass fraction.

20 March 2020 in Studia Universitatis Babeș-Bolyai Chemia
Verified
Journal Article
Open access
MMMladen Mirić
Mladen Mirić
BABiljana Arsic
Biljana Arsic
MƉMiloš ƉORĐEVIĆ
Miloš ƉORĐEVIĆ
DƉDragan Ɖorđević
Dragan Ɖorđević
DGDragoslav Gusković
Dragoslav Gusković
SISvetlana Ivanov
Svetlana Ivanov
Addition of different amounts of Cu and Ag to Au alloys, as well as some new elements (Zn and Cd), gives alloys of the different colour spectrum (from red to yellow) and different technological and metallurgical characteristics. The trend today is the implementation of new alloys not containing Ag, and including new elements, such as Ga and In. Differences in two Au alloys exist: the first alloy contains Ni and Pd, and the second alloy is without them. The values of electrical conductivity and hardness are different, due to the reduction, which was shown using PCA (r=0.985 and the strong positive correlation between hardness and electrical conductivity). Performed tests confirm that those multiphase multi component gold alloys can find their application not only in jewellery making but also in the world of modern electrical engineering. The performed statistical analysis shows strong positive and negative correlations of properties of investigated Au alloys, and it provides significant savings in the design and efficiency of metallurgical processes.