30 June 2022 in Eastern-European Journal of Enterprise Technologies
The object of this study is the technology of bus bodies and the formation of recommendations for design bodywork subject to the regulated durability of the body introduced into production. Advancing the technology of manufacturing bus bodies implies improving anti-corrosion protection, using new polymeric materials, and reducing the length of welds. The issue of corrosion resistance of bus bodies has been considered. It is established that the use of new polymeric materials will increase the corrosion resistance of bus bodies while existing technologies weakly protect against corrosion (resource up to 5 years). The peculiarity of this study is that the adhesion of new materials has been tested, with artificial aging, which confirms the durability of glued joints. According to the old technology, the body was exposed to anticorrosive treatment after welding the cladding with uncovered places left between the frame and body cladding, which provoked corrosion. The main idea is that in the new technology, the cladding is welded or glued after the body frame is fully coated with primer. New technologies and materials not used in the automotive industry have been proposed. Three variants of technologies were put into production. First: the welding of steel zinc sheets. In welding sites, the frame is covered with conductive primer. It was implemented for school buses (after 7 years, without damage). Second: gluing steel zinc sheets. It was implemented for city buses (after 6 years, without damage). Third: gluing sheets from composite materials not used in the automotive industry. The transition to new adhesive cladding technologies from composite corrosion-resistant materials instead of steel sheet, reduces by 2.5–3 times the length of welds (up to 20 years without damage). The studies have confirmed the strength of glued joints (cohesion rupture exceeds 95 %). The reliability of glued joints and high corrosion resistance of the body have been confirmed in the operation of buses. The scope of practical use of the results: bus-building plants. The reported results are suitable for production of all types while cataphoretic coatings are only for mass production
28 April 2023 in Eastern-European Journal of Enterprise Technologies
The object of this study is the processes and permissible limits of aging of bus bodies on the frame chassis during operation. As a result of research by simulation method, the durability of the bus on the frame chassis, was determined, which is in the range from 5 to 11 years depending on the operating conditions. The study took into account the following factors: passenger occupancy, microprofile of the road, bus speed, corrosion. The durability of the bus depends primarily on the durability of the frame and body frame. Since the frame is made of alloy steels and heat-treated, it is not repaired but replaced with a new one when cracks in the frame are formed. When determining the durability of the bus on the frame chassis, it was found that the frame has 1.5–1.8 times greater durability than the body frame itself. This is because the frame is made of alloyed materials and has an open structure. The body frame has closed cavities, which provoke the development of corrosion with the accumulation of moisture in them. A feature of the results is that previous studies considered buses only with a load-bearing body structure. The issue of durability of bodies on the frame chassis has been considered. As experience shows, the durability of bus bodies on a frame chassis depends on many operational factors. For operating organizations and manufacturing plants, it is important to provide for the durability of the bus depending on the operating conditions. The results of this study will allow operating organizations to provide for scheduled repairs, as well as take measures to increase the service life of buses during operation. For manufacturing plants, the findings will make it possible to apply rational technologies and materials to form the service life of the bus body.
30 April 2025 in Eastern-European Journal of Enterprise Technologies
The object of this study is the durability of a bus body when passengers are transported on rural roads. According to the European classification, the total length of roads in Ukraine that correspond to the first category does not exceed 5 %. That is, all other 95 % of roads have a quality level that does not meet the regulatory operating conditions. In particular, in rural areas, buses are operated both on worn asphalt-concrete surfaces and on dirt and gravel roads. Such operating conditions additionally lead to intensive wear of buses and significantly worsen the durability of their bodies. The task to determine the influence of worn and dirt roads on the durability of the bus body during passenger transportation in rural areas could be solved by the durability assessment procedure proposed in this paper. The current work presents patterns that make it possible to predict the degradation of the bus body material that affect the durability of the body. The factors of influence during the operation of buses on rural routes have been substantiated and presented. The simulation results show that when operating buses on rural roads, cracks in the body frame of the body occur at runs that are 3.8–13.1 times less than under regulatory operating conditions. The proposed procedure for assessing the durability of a bus body when transporting passengers on rural roads makes it possible to predict the deterioration of the physical and mechanical properties of the elements of the bus body frame and take measures at the design stage to increase their reliability and durability
10 April 2025 in Technology audit and production reserves
The object of research is the basic fuel consumption of a bus in standard urban cycles and identical conditions in real operation. Standard driving cycles are used to estimate fuel consumption. This allows consumers to compare buses and choose the best one, and manufacturers in the process of improving buses also allow them to estimate fuel consumption. However, sometimes standards may not correspond to reality. Therefore, specific routes are developed for some cities, which requires significant development costs. This problem is solved by collecting reliable information on average fuel consumption with an operating period of 1 year and bus mileage of 40–90 thousand km. As a rule, operating organizations do not provide such information. The development of electronic control systems allows to obtain information from “black boxes” additionally installed by the manufacturer, which record information throughout the entire service life of the bus. This approach is implemented in this work. Existing standards for determining fuel consumption in urban driving cycles are presented. The results of modeling and real tests are presented. Information was collected from the “black boxes” on fuel consumption on 12 buses for 1 year of operation with mileage from 40 to 90 thousand km on Ataman A092N6 buses. Fuel consumption was 16.4–21.2 l/100 km when operating buses in one city (the manufacturer claims up to 23 l/100 km). This makes it possible to solve the problem of collecting reliable information on fuel consumption based on year-round operation of buses, which has not been carried out in this format before. The results of this study will allow operating organizations to see the real fuel consumption on Ataman A092N6 buses in the city. Implementation of this approach on other buses will allow obtaining data for interested organizations similarly. This will allow estimating fuel consumption without additional tests, which will reduce research costs.
2 June 2023 in Bulletin of Cherkasy State Technological University
У роботі представлено новий метод мінімізації, що реалізує булеву функцію у класичній мінімальній формі представлення шляхом направленого перебору можливих шляхів мінімізації за критеріями необхідної і достатньої умови – індексний метод. Цей метод є продовженням еволюційного розвитку методів мінімізації шляхом зменшення значення базисного коефіцієнта К: методу мінімізації по частинах, методу паралельної декомпозиції шляхом зменшення К, матричного методу паралельної декомпозиції. Еволюція методів шляхом зменшення значення базисного коефіцієнта К йде шляхом досконалого вивчення будови та структурної організації множини булевих функцій, детального аналізу сильних і слабких сторін уже існуючих попередніх варіантів методів, виявлення критичних місць, що суттєво сповільнюють процес мінімізації, та пошуку альтернативних шляхів прискорення процесу мінімізації. Індексний метод розроблено на основі використання нового способу запису окремих булевих функцій у вигляді індексів значущих рядків таблиці істинності. Завдяки такій формі запису вдалося як реалізувати сильні сторони, шо використовували попередні методи, так і значно поліпшити слабкі етапи попередніх методів, що в цілому дає великий виграш у часі мінімізації. Перевагою методу є двоетапна мінімізація процесу, що дає можливість безпосередньо не використовувати критерій спрямованого сортування. При формуванні повного списку елементів одразу отримують елементи остаточної відповіді без зазначення проміжних результатів. Структурні елементи методу – повний набір можливих елементів кінцевої відповіді для булевих функцій, що містить одну кількість аргументів для значення базового коефіцієнта K=1...n, – формуються ще до початку виконання методу і використовуються як табличне значення. При реалізації методу в стовпцях таблиці істинності обробляються тільки одиниці без нулів, що зменшує кількість об'єктів обробки. Метод реалізується дворівневою обробкою стовпців – перевіркою необхідних і достатніх умов. Машинна реалізація методу використовує розпаралелювання процесу мінімізації. Все це істотно скорочує час мінімізації – основну цінність, що відрізняє цей метод від інших. Розроблений метод мінімізації є однією зі складових частин створення програмного коду, що є основою розробки фрактального комп’ютера. Головною особливістю фрактального комп’ютера є наявність у його програмному коді фрактальних (негладких) функцій, що дозволить радикально розширити його можливості в окремих областях обчислень. На сьогоднішній день жоден iз сучасних комп'ютерів не використовує ці функції в програмному коді.