Kenta Emori

Kenta Emori

Auto-generated profile, based on publicly available information

Kenta Emori

Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2022 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
KEKenta Emori
Kenta Emori
YKYutaka Kaneko
Yutaka Kaneko
HNHiroyuki Nishida
Hiroyuki Nishida
This study investigates the characteristics of flow-field patterns generated by burst-mode actuation of a dielectric-barrier-discharge plasma actuator in quiescent air. Particle-image velocimetry and background-oriented schlieren measurements conducted over a wide range of burst-signal parameters show that there are three types of flow-field patterns. Type 1 is the wall-surface jet seen in continuous mode actuation; type 2 features periodical independent vortices traveling along the wall surface; type 3 features such vortices moving away from the surface. The vortex sizes in types 2 and 3 are proportional to the energy consumed in generating one vortex. When the time-averaged jet velocity estimated by the power consumption is used as the characteristic velocity in the nondimensional scaling law, the time profiles of the vortex location in the type 3 flow-field pattern collapse into a single line, independently of the burst frequency and ratio. However, in the initial phase, the nondimensional vortex-core motion is better described using the jet velocity in continuous-mode actuation as the characteristic velocity. The transitions of the flow-field pattern from type 1 to type 3 result from interference between cyclically generated vortices and depend on the inter-vortex distances and the energy consumed in generating one vortex.

13 March 2023 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
AHAsami Hatamoto
Asami Hatamoto
KEKenta Emori
Kenta Emori
HNHiroyuki Nishida
Hiroyuki Nishida
Dielectric barrier discharge plasma actuators (DBDPAs) have been investigated for active flow control. The discharge induces ionic wind, which can be utilized for flow control; however, it simultaneously heats the flow and the dielectric surface. The thermal characteristics of the DBDPA must be clarified for applications in thermo-fluid engineering, such as forced convective cooling. In this study, we constructed a similarity law for the time variation of the surface temperature, assuming that the induced flow was heated by the discharge and that the dielectric was heated by the airflow. The similarity law was derived from the one-dimensional heat conduction equation in the dielectric, and the spatially averaged normalized temperature was then formulated as a function of the Biot and Fourier numbers. To experimentally validate the similarity law, the surface temperature, thrust, and power consumption were measured. The induced flow temperature and heat transfer coefficient were estimated based on the thrust and power consumption. The measured results verified that the similarity law was valid, regardless of the dielectric material, thickness, or applied voltage. This result supports the hypothesis regarding the heating mechanism in which the airflow is heated by Joule heating and the dielectric is heated by forced convection.

21 November 2022 in Actuators
Verified
Journal Article
Open access
PDF file
KEKenta Emori
Kenta Emori
YKYutaka Kaneko
Yutaka Kaneko
HNHiroyuki Nishida
Hiroyuki Nishida
The flow field produced by a dielectric-barrier-discharge plasma actuator using burst modulation was experimentally investigated in quiescent air from two viewpoints: density and vorticity fields. A wide range of burst signal parameters were evaluated using particle-image velocimetry and background-oriented schlieren measurements. Four types of flow-field patterns were found: Type 1 was a wall jet, similar to continuous operation; Type 2 was a periodical, independent vortex moving along the wall surface; Types 3 and 4 demonstrated a feature wherein the periodic shedding of the vortex pair (primary and secondary vortices) occurred while moving over the surface. While Types 3 and 4 demonstrated a shared feature, they had different density and vorticity structures. The change of the flow-field pattern from Type 1 to Type 4 was triggered by a lower burst frequency and ratio, as well as a higher base frequency. In addition, the vorticity strength and density were strongly negatively correlated and depended on the rate of power consumption to generate one vortex.