In this work, the impregnation quality and mechanical properties of Pinus radiata D.Don treated with different copper nanoparticles (CuNP) solutions (named K1 and K2) and a commercial preservative (M) were studied. The impregnation quality of radiata pine wood was analyzed by two indicators, penetration and retention. The micro-distribution of preservative in the treated wood was qualitatively evaluated by SEM-EDS, both in the samples containing CuNP and in those treated with the commercial preservative. In addition, some mechanical properties were studied in the preserved wood including MOE, MOR and hardness. The results indicated values by ED XRF retention of 0.96 kg/m³ and 0.86 kg/m³ for K1 and K2, respectively, and 1.01 kg/m³ for M wood impregnated. In the penetration determined by colorimetric test, the wood samples impregnated (with K1, K2 and M) showed 100% penetration. The distribution of CuNP and micronized copper within the wood structure was confirmed by SEM EDS mapping. In mechanical properties, a reduction in MOE was reflected in all wood treated. The control samples were far superior to the K1 and M treated samples and slightly superior to the K2 samples, with no statistically significant differences. On the other hand, samples impregnated with K1 and K2 showed the highest values in hardness parallel and perpendicular to the grain, revealing that these preservative solutions tend to increase hardness. Overall, when it comes to the samples impregnated with micronized copper (M), the mechanical properties were considerably lower compared to the CuNP treated and control wood. Therefore, the CuNP-based preservative did not strongly affect the mechanical properties of the preserved wood.

Wood is a sustainable and renewable material with a lower carbon footprint than other materials. However, its transformation into engineered products industrially, such as glulam, requires kiln drying, which implies energy consumption and loss of wood resources. Recent research has carried out green gluing, a variant of glulam characterized by a reduction of the drying process. Interest in it has increased as a new method of improving the use of wood that does not meet industry standards. It has been accomplished by developing adhesives for wood with high moisture content, but the variables involved are not yet completely understood. Therefore, conducting further research and analyzing the relevant publications is necessary. Bibliometric analysis was the method used, which included documents stored (from 2000 to 2020) in Scopus (Elsevier), Web of Science (Clarivate Analytics), and SciELO Citation Index (Web of Science—Clarivate Analytics) databases. The bibliometric analysis identified three main areas to develop: glue wood, glue properties, and analysis methods. The studies were concentrated on a few countries and research groups. The main progress has been made in synthetic and natural (or environmentally friendly) glue topics. The improvement of technique could enlarge the opportunities for collaboration and innovation in wood material science.

Structural lumber is designed to meet the technical standards that ensure safety, cost-effectiveness, and sustainability. However, some tree species face limitations in their growth, which restricts their widespread use. An example of this is Nothofagus alpina, which has excellent mechanical properties but is not utilized much due to the challenges in extracting its timber and poor utilization, mainly because of the length of the wood. There is little information concerned with the uses and better management of small pieces using Nothofagus species, but it is still insufficient. This study investigates the adhesion performance of green-glued finger joints with varying wood ring orientations and moisture contents ranging from 21% to 25% using Nothofagus alpina. The primary aim is to assess how ring orientation and wet timber affect the green gluing process for creating larger wood pieces than sawn wood. The resulting products could meet the standards for wood serviceability number three for native Chilean wood. The findings indicate that finger joint performance improves with higher timber moisture levels. However, the orientation of the wood fibers did not significantly affect the performance under the tested conditions. It is important to note that this effect may become more significant near the fiber saturation point. These findings emphasize the need for a detailed protocol on the green gluing technique for Nothofagus alpina and the associated drying and surface processes in finger joint construction.

This study aimed to develop a model using experimentally obtained convective heat and mass transfer coefficients to predict the effect of temperature, humidity, and drying rate on wood drying. Tangential wood samples of Eucalyptus nitens (H. Deane & Maiden) were used in the investigation. The experimental design consisted of two temperature levels (40 °C and 55 °C), two relative humidity levels (55% and 75%), and two air velocity settings (2 m·s⁻¹ and 3 m·s⁻¹). The experiments were conducted under a constant evaporation rate, spanning the maximum and critical moisture content in the wood. A statistical model using multivariate regression was created to predict the convective heat and mass transfer coefficients. The results indicated that the experimental data and empirical correlations exhibited an error margin of 37.77% and 37.86%, respectively. A significant positive correlation was found between the convective heat transfer coefficient and air velocity, temperature, and relative humidity, while the convective mass transfer coefficient showed a significant positive correlation only with air velocity and temperature. The model predicted the convective heat and mass transfer coefficients with high accuracy and statistical significance. Using the proposed method, we successfully obtained both convective coefficients, which enable accurate description of heat and mass flow during the convective drying of Eucalyptus nitens wood.

Appraising and protecting forests requires a management plan and the creation of innovative products for the market. The development of the green gluing technique could add value to native timber. However, there is a lack of knowledge concerning the response and the productive process of Nothofagus species using this technique. This work investigated the viability of implementing the green gluing method using three types of Nothofagus. Wood pieces were made using a one-component polyurethane adhesive. Delamination, shear tests, morphological characterization, and bond line thickness analysis tested their capacity. The results showed a variable response depending on the Nothofagus type, where the surface treatment could improve the green gluing performance. The findings highlight the relevance of increasing knowledge about the essayed species and their preparation to maintain their natural moisture condition.