Dmitry Vladimirovich Dudka

Dr. Dmitry Vladimirovich Dudka

A.V. Topchiev Institute of Petrochemical Synthesis, Moscow, Moskva, Russia
orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Alexander MalkinAlexander Malkin
Alexander Malkin
ЛТЛадыгина Т.А.
Ладыгина Т.А.
GSGusarov Сергеевич Sergey
Gusarov Сергеевич Sergey
DDDmitry Vladimirovich Dudka
Dmitry Vladimirovich Dudka
AMAnton V. Mitiukov
Anton V. Mitiukov
The molecular characteristics and rheological properties of three UHMWPE samples were investigated. The high-temperature GPC method was used for characterizing UHMWPE samples used. The interpretation of the measurement results was based on calibration using the PS standard and the approximation of the PS data by linear and cubic polynomials, as well as on the data for linear PE. The assessment of the average MW and MWD depends on the choice of calibration method, so that different methods give different results. Only the results obtained using PS with cubic approximation are close to the characteristics offered by the manufacturer. It was also shown that the obtained MW characteristics depend on the dissolution time. The reason for this may be the presence of any processing-aid compounds or destruction of macromolecules. Measurements of the rheological properties were performed in creep modes for a wide range of shear stresses and harmonic oscillations. It was shown that even at 210 °C, UHMWPE does not flow, and the observed irreversible deformations are due to the plasticity of the polymer, i.e., UHMWPE is in an elastic–plastic state. The ultimate plastic deformations drop sharply with increasing MW of the polymer. The plasticity modulus for the highest molecular weight UHMWPE samples does not depend on stress. Measurements of viscoelastic characteristics confirmed that the terminal region of viscous flow cannot be reached under any conditions. Increasing the duration of holding the polymer at high temperature leads not to flow, but to the destruction of macromolecules.

28 January 2026 in Polymers
Verified
Journal Article
Open access
PDF file
DDDmitry Vladimirovich Dudka
Dmitry Vladimirovich Dudka
ASAzamat Slonov
Azamat Slonov
KMKhasan V. Musov
Khasan V. Musov
ATAslanbek F. Tlupov
Aslanbek F. Tlupov
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
Alexander MalkinAlexander Malkin
Alexander Malkin
Powder Injection Molding (PIM) is a versatile manufacturing technology widely used for fabricating components with complex geometries from metals and ceramics, yet its application to high-performance thermoplastics remains underutilized. This study explores the feasibility of manufacturing products from Polyphenylene Sulfide (PPS)—a promising linear aromatic polymer synthesized in powder form—using PIM technology and investigates the development of PE-based feedstocks with PPS and solid fillers. Regarding the matrix formulation, it was found that using pure paraffin as a binder limited the maximum PPS content to 20%. Consequently, a modified binder system consisting of Low-Density Polyethylene (LDPE) and paraffin in a 70:30 wt.% ratio was utilized, which successfully increased the PPS loading in the feedstock to 50% and enabled stable molding. Following matrix optimization, the study examined composites incorporating various fillers, including chalk, talc, and carbon fibers. Systematic rheological analysis confirmed that these composite suspensions possess characteristics necessary for molding products with complex geometries. Key results indicate that optimal sintering conditions were established to achieve the required mechanical properties. Among the tested fillers, carbon fibers were the most effective reinforcement, increasing the elastic modulus by 33% and flexural strength by 20%. Representative examples of samples successfully manufactured via this approach are presented.

15 May 2025 in Polymers
Verified
Journal Article
Open access
PDF file
PMPavel A. Mikhaylov
Pavel A. Mikhaylov
AMAnton V. Mitiukov
Anton V. Mitiukov
DDDmitry Vladimirovich Dudka
Dmitry Vladimirovich Dudka
YGYaroslav Golubev
Yaroslav Golubev
Valery KulichikhinValery Kulichikhin
Valery Kulichikhin
Alexander MalkinAlexander Malkin
Alexander Malkin
Thermotropic polyesters are a subject of keen interest due to their exceptional heat resistance, thermal stability, and high strength. However, these thermal characteristics pose significant constraints on standard manufacturing processes, as the melting temperatures of these polymers can exceed 300 °C. This study explored the feasibility of manufacturing final items molded from prepolymers through a solid-state polymerization process. A copolymer composed of 4-acetoxybenzoic acid (4ABA), 3-acetoxybenzoic acid (3ABA), and 4′-acetoxybiphenyl-4-carboxylic acid (ABCA) was synthesized using melt polycondensation. To comprehensively evaluate the performance of the resulting material, several sets of samples were prepared, including those containing TiO2. Experimental samples from the pre-polymers were obtained through injection molding followed by high-temperature solid-state post-polymerization. The final products underwent a range of tests, including rheological and mechanical analyses, as well as thermal evaluations. The products demonstrated sufficient strength and stability. The proposed method of solid-state post-condensation offers significant potential advantages for the practical application of manufacturing high-performance engineering materials.

14 November 2025 in Proceedings
Verified
Conference Paper
Open access
PDF file
DDDmitry Vladimirovich Dudka
Dmitry Vladimirovich Dudka
AMAnton V. Mityukov
Anton V. Mityukov
Alexander MalkinAlexander Malkin
Alexander Malkin
IGIrina Yu. Gorbunova
Irina Yu. Gorbunova
Ultra-high-molecular-weight polyethylene (UHMWPE) has attracted substantial scientific attention since its inception in industrial production owing to its exceptional properties, such as high tensile strength, superior wear resistance, chemical inertness, and a low coefficient of friction