Azamat Slonov

Mr. Azamat Slonov

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2018 in Rapid Prototyping Journal
Verified
Journal Article
Closed access
ASAzamat Slonov
Azamat Slonov
AKAzamat Askerovich Khashirov
Azamat Askerovich Khashirov
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
ERElena Rzhevskaya
Elena Rzhevskaya
SKSvetlana Khashirova
Svetlana Khashirova
Purpose: This paper aims to examine the impact of three-dimensional (3D) printing technological modes (using fused deposition modelling [FDM]) on physical and mechanical properties of samples from polyphenylenesulfone. Design/methodology/approach: For this study, the standard test samples were printed using the FDM method at different filament orientation angles, the gaps between them and a different width. The basic physical and mechanical properties, such as the strength, the elastic modulus and the impact strength, were studied. Findings: The authors found that the basic mechanical properties strongly depend on the printing settings. In particular, the elastic modulus generally depends on the air gap between rasters, and it is practically independent of the filament orientation angle. In contrast, the impact strength depends on the orientation and the degree of adhesion between filaments: the highest values are reached at the longitudinal orientation of rasters in the sample (0°) and the minimum value of the air gap (−0.025 mm). However, in selecting the optimal mode of 3D printing, it is necessary to take into account the specific geometry of the printing products and the direction of the stress that it will experience. Originality/value: The paper presents the results of the investigation of the influence of FDM printing modes on the mechanical properties of samples from polyphenylenesulfone, including impact strength. The authors studied the mechanisms of the destruction under impact loading and revealed the optimal printing settings for making samples with properties which are not inferior to the injection molded samples.

14 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
ASAzamat Slonov
Azamat Slonov
IMIsmel Musov
Ismel Musov
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
ZKZhanna Inalovna Kurdanova
Zhanna Inalovna Kurdanova
KSKamila Shakhmurzova
Kamila Shakhmurzova
SKSvetlana Yu. Khashirova
Svetlana Yu. Khashirova
Polyphenylene sulfones (PPSU) blends with different viscosities have been studied. It is shown that the blends have a single-phase structure, regardless of the viscosities of the mixed polymers. It was found that blends having close values of the melt flow index (MFR) are also characterized by a similar melt viscosity in a wide range of shear rates, regardless of the viscosities of its constituent components. It has been found that PPSU blends with smaller MFR differences exhibit higher heat resistance and stability of mechanical properties, while blends with similar viscosity containing oligomers exhibit a broader molecular weight distribution (MWD) and have lower thermal and mechanical properties.

18 October 2023 in Polymers
Verified
Journal Article
Open access
PDF file
ASAzamat Slonov
Azamat Slonov
IMIsmel Musov
Ismel Musov
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
AKAzamat Khashirov
Azamat Khashirov
ATAslanbek Tlupov
Aslanbek Tlupov
SKSvetlana Yu. Khashirova
Svetlana Yu. Khashirova
3D printing of polyolefins, such as polyethylene (PE) and polypropylene (PP), is of great practical interest due to the combination of high properties of these materials. However, the use of these materials in 3D printing is associated with many problems due to their high rate of crystallization, which causes shrinkage and warpage of the printed object. In this regard, blends of PE and ethylene-vinyl acetate copolymer (EVA) of various compositions were investigated for 3D printing. It was found that with an increase in the concentration of EVA, an increase in the pseudoplastic effect and amorphization of PE occurs. It has been shown that with an increase in the EVA content, the degree of crystallinity of PE decreases slightly (by 11% at a content of 80% EVA); however, a significant decrease in the rate of crystallization of PE is observed (by 87.5% at the same EVA concentration). It was found that PE and EVA are completely compatible in the amorphous phase and partially compatible in the crystalline phase, which leads to a slight decrease in the melting point of PE. The introduction of EVA also leads to a significant increase in impact strength: the maximum value is achieved at a 50/50 ratio, which is five times the value of the initial PE and two times the value of the initial EVA. At the same time, it was revealed that EVA leads to a gradual decrease in the elastic modulus and strength of PE, the change of which generally obeys the additivity rule. The resulting printing filaments are characterized by a certain ovality due to their shrinkage, which decreases with increasing EVA content and reaches a minimum value at a PE/EVA ratio of 30/70. This composition also demonstrates the lowest shrinkage of the printed sample and higher processability during printing.

4 May 2020 in Polymers
Verified
Journal Article
Open access
PDF file
ASAzamat Slonov
Azamat Slonov
IMIsmel Musov
Ismel Musov
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
ERElena Rzhevskaya
Elena Rzhevskaya
DKDiana Khakulova
Diana Khakulova
SKSvetlana Yu. Khashirova
Svetlana Yu. Khashirova
The effect of oligophenylene sulfone (OPSU) and polycarbonate (PC) on the rheological, mechanical and thermal properties of polyetherimide (PEI) and a carbon-filled composite based on it was studied. It is shown that the introduction of OPSU and PC leads to a decrease in the melt viscosity of PEI and a carbon-filled composite based on it with the preservation of their mechanical properties and heat resistance at a sufficiently high level. It was found that composites with OPSU have higher mechanical and thermal properties compared with composites with PC. Samples from modified carbon-filled PEI were printed by the fused deposit modeling (FDM) method. Three-dimensionally printed samples from carbon-filled PEI modified by OPSU showed significantly higher mechanical properties than composites with PC.

12 May 2023 in Polymers
Verified
Journal Article
Open access
PDF file
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
ZKZhanna Inalovna Kurdanova
Zhanna Inalovna Kurdanova
KSKamila Shakhmurzova
Kamila Shakhmurzova
ASAzamat Slonov
Azamat Slonov
Ilya BorisovIlya Borisov
Ilya Borisov
SKSvetlana Yu. Khashirova
Svetlana Yu. Khashirova
For the first time, the effect of the solvent and monomer ratio on molecular weight, chemical structure, and mechanical, thermal, and rheological characteristics of polyphenylene sulfone has been studied. When dimethylsulfoxide (DMSO) is used as a solvent, cross-linking occurs during the processing of the polymer, which is accompanied by an increase in melt viscosity. This fact sets a pressing need for the complete removal of DMSO from the polymer. The best solvent used for the production of PPSU is N,N-dimethylacetamide. This study of the molecular weight characteristics of polymers by gel permeation chromatography showed the stability of the polymers practically does not change with a decrease in molecular weight. The synthesized polymers correspond in tensile modulus to the commercial analog Ultrason-P, while exceeding it in terms of tensile strength and relative elongation at break. Thus, the developed polymers are promising for spinning hollow fiber membranes with a thin selective layer.

26 October 2021 in Polymers
Verified
Journal Article
Open access
PDF file
ZKZhanna Inalovna Kurdanova
Zhanna Inalovna Kurdanova
AZAzamat Aslanovich Zhansitov
Azamat Aslanovich Zhansitov
KSKamila Shakhmurzova
Kamila Shakhmurzova
ASAzamat Slonov
Azamat Slonov
ABArtur Baykaziev
Artur Baykaziev
SKSvetlana Yu. Khashirova
Svetlana Yu. Khashirova
Copolymers based on 4,4′-dihydroxydiphenyl, phenolphthalein and 4,4′-dichlorodiphenyl sulfone were synthesized by the method of high temperature polycondensation. The structure of the synthesized copolymers was confirmed by IR spectroscopy. Their physical, mechanical and thermal properties were investigated. It is shown that increases in the content of carded fragments lead to higher glass transition temperatures and heat resistance of the copolymers, as well as higher elastic and strength properties.