Kirill Igorevich Doronin

Mr. Kirill Igorevich Doronin

Metrology, Instrumentation and Quality Management, Saint Petersburg Mining University, Saint Petersburg, Sankt-Peterburg, Russia
orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2025 in International Review on Modelling and Simulations (IREMOS)
Verified
Journal Article
Closed access
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
KGKirill Valerievich Gogolinskiy
Kirill Valerievich Gogolinskiy
AUAlexander Sergeevich Umanskii
Alexander Sergeevich Umanskii

18 April 2025 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
AVAnna Vinogradova
Anna Vinogradova
Kirill GogolinskyKirill Gogolinsky
Kirill Gogolinsky
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
ESEkaterina Shchiptsova
Ekaterina Shchiptsova
AMAlena Melnikova
Alena Melnikova
The paper analyzes the process of indentation of polymeric materials with a spherical indenter. The loading diagrams P(h) obtained experimentally and by means of finite element method (FEM) are analyzed. The material under study was high-density polyethylene (HDPE) of PE100 grade, taken from a pipeline for gas distribution systems. The aim of the work was to determine the parameters of the computer model, taking into account hardening and creep processes when verifying P(h) diagrams with experimental studies. The influence of variation of the parameters of the calculation formulas on the reliability of the simulation results was analyzed. The results of the calculation of mechanical properties of material on the basis of P(h) diagrams by the Oliver–Pharr method for model and experimental diagrams were compared. The possibility of using computer modeling for the analysis of instrumented indentation processes is demonstrated, since the results revealed the convergence of the elastic modulus of 1078 GPa for FEM and 1083 GPa for the experiment. The conformity of the Oliver–Pharr method for determining the contact depth is also shown, which differed from the model geometry by only 2.3%. Simulation of the indentation process using the Norton model via FEM, as well as determining the parameters of the material deformation function while taking creep into account, makes it possible to describe the process of contact interaction and shows good agreement with experimental data.

24 September 2026 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
AIAleksandr Ilinskii
Aleksandr Ilinskii
AUAleksandr Umanskii
Aleksandr Umanskii
AKArtem Kondratev
Artem Kondratev
In this work, the load-dependent indentation response of as-built Inconel 718 produced by direct laser deposition was studied, followed by local mapping around a single surface-intersecting pore. A working load of 100 mN was selected because the indentation modulus approached a depth-independent plateau and the penetration depth was substantially larger than the measured surface roughness. At this load, the reference matrix response was HIT = 2.69 ± 0.26 GPa and EIT = 160 ± 11 GPa. An equivalent contact radius ac was calculated from the projected contact area, and pore-edge distance was normalized as ξ = s/ac. For the reference response, ac ≈ 3.44 µm and the first numerically defined position at s = 20 µm corresponded to ξ ≈ 5.8. Robust regression of 56 individual measurements showed no statistically resolved dependence of EIT on ξ, whereas a small negative HIT slope was observed and interpreted cautiously because of directional variability. The analysis is restricted to this single pore and to ξ ≥ 5.8; the immediate pore-edge regime was not experimentally resolved. The contact-scale normalization provides a reproducible framework for interpreting local indentation data near a geometrical defect without treating the two-dimensional pore-area fraction as bulk porosity.

1 January 2026 in Reviews on Advanced Materials and Technologies
Verified
Journal Article
Closed access
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
AUAleksandr Umanskii
Aleksandr Umanskii
AKA.V. Kondratev
A.V. Kondratev
This work is devoted to mechanical properties estimation of steel samples produced by additive and classic technologies via instrumented indentation test. Features of 3D printing, physical and mechanical properties, methods and means of additive manufacturing products control are described. The experimental part presents a series of indentation tests to determine the parameters of elastic-plastic deformation: hardness and elastic modulus, which are compared to reference data from other studies. The difference in the properties of the material produced by classical technologies and synthesized by direct metal laser sintering (DMLS) from a powder of identical chemical composition is discussed. The elastic modulus varied less for DMLS samples (208–213 GPa) than for cast ones (203–234 GPa). Hardness of the additively manufactured 12Cr18Ni10Тi was also more consistent relative to the differently remelted samples.

23 August 2024 in Defektoskopiâ
Verified
Journal Article
Closed access
PDF file
KGK. V. Gogolinskii
K. V. Gogolinskii
AUA. S. Umanskii
A. S. Umanskii
AGArtem Golev
Artem Golev
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
KTK. A. Tomsky
K. A. Tomsky
The results of a comparative analysis of three methods for calculating the elastic modulus during dynamic instrumental indentation are presented: in accordance with GOST R 56474, GOST R 8.748 and the proposed original method based on data from optical analysis of the indentation using prepared samples of alloys 20Х25Н20С2, 20Х23Н18 and BrANZhNMts9-4-4- 1.

15 June 2024 in Defektoskopiâ
Verified
Journal Article
Closed access
PDF file
OKO. A Kolganov
O. A Kolganov
Kirill Igorevich DoroninKirill Igorevich Doronin
Kirill Igorevich Doronin
AGArtem Golev
Artem Golev
The issues of improving the accuracy of estimating the indenter motion parameters in the primary converter of a dynamic instrumented indentation device using two counter-connected coil windings (differential coil) are considered. The calculation of the characteristics of the primary converter is based on computer modeling and solving the problem of step-by-step conditional optimization of the relative dimensions of the striker magnet and coil. The results of a study of a primary converter with a differential coil (comparative estimates of the recorded signal — EMF and the dynamic modulus of elasticity of steel St.3) in relation to the existing primary sensor converter of the TPTS-7 device, which showed its advantage.