Hydrological cycle research requires a detailed analysis of the involved parameters to understand watershed behavior comprehensively. In recent decades, both Geographic Information Systems (GIS) and Digital Elevation Models (DEMs) were implemented and took a substantial role in watershed geomorphological parameterization; however, the variability of these instruments remains a challenge, together with high-resolution DEMs being unavailable, requiring digital processing to improve resolution. This research aims to merge DEMs and evaluate GIS geoprocessing algorithms to determine drainage networks and the geomorphological parametrization of a semiarid watershed. DEMs with resolutions of 1.5, 5, 12.5, and 30 m, the Jenson/Domingue (J/D) and Wang/Liu (W/L) fill algorithms; and D8, D, KRA, and MFD flow routing algorithms were used. One of the research findings proved that the divergences of the drainage networks are mainly attributed to filling algorithms and not flow routing algorithms; the shifts between the networks obtained in the processes reach horizontal distances up to 300 m. Since the water movement within the watershed depends on geomorphological characteristics, it is suggested that DEM-based hydrological studies specify both the resolution and the algorithms used in the parametrization to validate the rigidity of the research, improving estimate areas of high hydrological risk.

A transformation-induced plasticity (TRIP) steel and a dual-phase (DP) steel were paired together by employing gas metal arc welding (GMAW) and laser beam welding (LBW) processes. The post-weld microstructure, the hardness profile, and the uniaxial tensile behavior of the welded steels have been analyzed in detail. The experimental surface residual stress distribution across the weldment was measured through the X-ray diffraction sin²Ψ technique. The results indicate that although a harder microstructure composed of predominant martensite was observed along the weldment, the uniaxial tensile behavior resulted in better elongation properties and a higher UTS in the LBW specimen as compared to the GMAW specimen. The resultant residual stress distribution in the heat-affected zone (HAZ) had an increase to a maximum value, followed by a steady decrease up to the base metal following the trend: upper-critical UC-HAZ (maximum) → inter-critical IC-HAZ (moderated) → subcritical SC-HAZ (lowered), which was particularly more evident on the GMAW specimen. Overall, the resultant residual stresses along the weldment were lower on the LBW specimen (172 MPa maximum) which clearly contrasts to the GMAW specimen (421 MPa maximum). Finally, the tensile residual stresses in both the GMAW or LBW did not influence the overall tensile properties of the weldments.

Dual Phase (DP) steel, composed of a ferrite matrix with dispersed islands of martensite, has become popular in auto-body car construction due to its outstanding mechanical properties (i.e., high strength and good ductility). DP steel softens at the sub-critical heat-affected zone (SC-HAZ) when subjected to welding thermal cycles, owing to the tempering of the martensite phase. In this work, DP980 steel was subjected to varied thermal cycles: (a) furnace-tempering treatment, (b) gas metal arc welding (GMAW), and (c) resistance spot welding (RSW), in order to characterize the tempering of martensite below the Ac₁ critical temperature and at the sub-critical heat-affected zone (SC-HAZ) in the case of the welded specimens. The coarsening stage of cementite phase was characterized through microstructure observations and hardness measurements. As expected, the comparative results indicated an advanced stage of the martensite tempering in the furnace heat-treated specimens, followed by the GMAW and the RSW specimens. Further, developed softening kinetic models have been suitably employed and adjusted in order to predict the extent of softening along the SC-HAZ of the GMAW specimen. Finally, as the advanced stage of cementite coarsening is due to the influence of the arc welded thermal cycle, a reasonable estimation of the hardness profile was obtained, particularly for tempering temperatures above 400 °C.

In the present study, the microstructure evolution of WC-10Co-4Cr powder deposited on AISI-SAE 1020 steel substrate by laser cladding was evaluated, considering the effect of average energy per unit area. Single tracks were obtained by employing a Yb: YAG laser system with selected processing parameters. All samples were sectioned in the transverse direction for further characterization of the cladding. Results showed that dilution lay within 15% and 25%, whereas porosity was measured below 12%. According to microstructural analyses, considerable grain growth is developed within the central area of the cladding (namely, the inner region); additionally, the development of a triangular and/or polygonal morphology for WC particles along with a clear reduction in hardness was observed when employing a high average energy. It is worth noting that, in spite of the rapid thermal cycles developed during laser cladding of WC-10Co-4Cr, grain growth is attributed to a coalescence mechanism due to complete merging of WC into larger particles. Finally, the presence of small round or ellipsoidal particles within the inner region of the cladding suggested that non-merged particles occurred due to both an inhomogeneous dispersion and the lack of faced-shaped WC particles.

An ultra-high-strength press-hardening steel (PHS) and a high-strength dual-phase steel (DP) were butt-joined by the gas metal arc welding (GMAW) process, aiming to assess the effects of a high heat input welding process on the structure-property relationship and residual stress. The post-weld microstructure, the microhardness profile, the tensile behavior, and the experimentally obtained residual stresses (by x-ray diffraction) of the steels in dissimilar (PHS-DP) and similar (PHS-PHS, DP-DP) pair combinations have been analyzed. Results indicated that the ultimate tensile strength (UTS) of the dissimilar pair PHS-DP achieves a similar strength to the DP-DP joint, whereas the elongation was similar to that of the PHS-PHS weldment. The failure location of the tensile specimens was expected and systematically observed at the tempered and softer sub-critical heat-affected zone (SC-HAZ) in all welded conditions. Compressive residual stresses were consistently observed along the weldments in all specimens; the more accentuated negative RS were measured in the PHS joint attributed to the higher volume fraction of martensite; furthermore, the negative RS measured in the fusion zone (FZ) could be well correlated to weld restraint due to the sheet anchoring during the welding procedure, despite the presence of predominant ferrite and pearlite microstructures.

This work reports on the fabrication of a novel two-layer material composed of a porous tantalum core and a dense Ti6Al4V (Ti64) shell by powder metallurgy. The porous core was obtained by mixing Ta particles and salt space-holders to create large pores, the green compact was obtained by pressing. The sintering behavior of the two-layer sample was studied by dilatometry. The interface bonding between the Ti64 and Ta layers was analyzed by SEM, and the pore characteristics were analyzed by computed microtomography. Images showed that two distinct layers were obtained with a bonding achieved by the solid-state diffusion of Ta particles into Ti64 during sintering. The formation of β-Ti and α′ martensitic phases confirmed the diffusion of Ta. The pore size distribution was in the size range of 80 to 500 µm, and a permeability value of 6 × 10⁻¹⁰ m² was close to the trabecular bones one. The mechanical properties of the component were dominated mainly by the porous layer, and Young’s modulus of 16 GPa was in the range of bones. Additionally, the density of this material (6 g/cm³) was much lower than the one of pure Ta, which helps to reduce the weight for the desired applications. These results indicate that structurally hybridized materials, also known as composites, with specific property profiles can improve the response to osseointegration for bone implant applications.