This paper presents a new technique of electrical energy generation using mechanically excited piezoelectric materials and a nonlinear process. This technique, called synchronized switch harvesting (SSH), is derived from the synchronized switch damping (SSD), which is a nonlinear technique previously developed to address the problem of vibration damping on mechanical structures. This technique results in a significant increase of the electromechanical conversion capability of piezoelectric materials. Comparatively with standard technique, the electrical harvested power may be increased above 900%. The performance of the nonlinear processing is demonstrated on structures excited at their resonance frequency as well as out of resonance.
1 February 2006 in Sensors and Actuators A: Physical
This article presents a nonlinear approach to optimize the power flow of vibration-based piezoelectric energy-harvesting devices. This self-adaptive principle is based on a particular synchronization between extraction of the electric charge produced by the piezoelectric element and the system vibrations, which maximizes the mechanical to electrical energy conversion. An analytical expression of the optimal power flow is derived from a simple electromechanical model. An electronic circuit designed to perform the synchronous charge extraction is proposed. Theoretical predictions confirmed by experimental results show that the new principle increases the harvested power by 400% as compared with a quasilinear impedance adaptation optimization method.
10 September 2007 in IEEE Transactions on Power Electronics
This paper presents a comprehensive model for miniature vibration-powered piezoelectric generators and analyses modes of operation and control of a buck-boost converter for the purpose of tracking the generators optimal working points. The model describes the generator's power dependence with the mechanical acceleration and frequency, and helps in the definition of the load behaviour for power optimization. Electrical behaviour of the input of buck-boost converter in discontinuous current mode turns out to be in perfect agreement with the considered optimization criteria with a very simple, sensorless control. Experimental results show that the converter controlled by a very low consumption circuit effectively maximizes the power flow into a 4.8 V rechargeable battery connected to the converter output. The converter's efficiency is above 84% for input voltages between 1.6 and 5.5 V, and for output powers between 200 muW and 1.5 mW. The presented circuit and control can be used as well for power optimization of electromagnetic energy harvesting devices.
31 March 2008 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
In the framework of microgenerators, we present in this paper the key points for energy harvesting from temperature using ferroelectric materials. Thermoelectric devices profit from temperature spatial gradients, whereas ferroelectric materials require temporal fluctuation of temperature, thus leading to different applications targets. Ferroelectric materials may harvest perfectly the available thermal energy whatever the materials properties (limited by Carnot conversion efficiency) whereas thermoelectric material's efficiency is limited by materials properties (ZT figure of merit). However, it is shown that the necessary electric fields for Carnot cycles are far beyond the breakdown limit of bulk ferroelectric materials. Thin films may be an excellent solution for rising up to ultra-high electric fields and outstanding efficiency. Different thermodynamic cycles are presented in the paper: principles, advantages, and drawbacks. Using the Carnot cycle, the harvested energy would be independent of materials properties. However, using more realistic cycles, the energy conversion effectiveness remains dependent on the materials properties as discussed in the paper. A particular coupling factor is defined to quantify and check the effectiveness of pyroelectric energy harvesting. It is defined similarly to an electromechanical coupling factor as k2 = p2thetas0/(epsivthetas33CE), where p, thetas0, epsivthetas33, Ce are pyroelectric coefficient, maximum working temperature, dielectric permittivity, and specific heat, respectively. The importance of the electrothermal coupling factor is shown and discussed as an energy harvesting figure of merit. It gives the effectiveness of all techniques of energy harvesting (except the Carnot cycle). It is finally shown that we could reach very high efficiency using lang111rang0.75Pb(Mg1/3Nb2/3)-0.25PbTiO3 single crystals and synchronized switch harvesting on inductor (almost 50% of Carnot efficiency). Finally, practical implementation key points of pyroelectric energy harvesting are presented showing that the different thermodynamic cycles are feasible and potentially effective, even compared to thermoelectric devices.
7 November 2002 in IEEE Transactions on Industrial Electronics
Multicell converters were introduced ten years ago and, over this period, their properties have been thoroughly analyzed. Since then, this concept has lead to some other innovative topologies which are briefly presented in this paper. Different ways to introduce soft switching in multicell converters are investigated. The concept of distributing power over several switches, giving more degrees of freedom and using less passive components, is extended further with the stacked multicell topology. Finally, direct AC-AC converters using the multicell approach are described.