This study examines the potential use of wash fines, a waste product from concrete plant cleaning, as supplementary cementing materials (SCMs) in mortars. The main objective is to assess the feasibility and benefits of this incorporation in terms of technical performance and environmental impact. Extensive tests were carried out on different mortar formulations, incorporating varying rates of washing fines (0%, 10%, 20%, 30%) as a partial replacement for cement. This choice of replacement is prompted by the fineness of washing fine particles. The properties studied included compressive and flexural strength, porosity, density, water absorption, shrinkage and fire resistance. The results show that the incorporation of washing fines increases porosity and decreases mortar density. There was also a decrease in mechanical strength and fire resistance as the substitution rate increased. However, the use of washing fines enables a significant reduction in the mortar’s carbon footprint, reaching up to 29% for the formulation with 30% substitution. This study demonstrates the potential of washing fines as an alternative SCM, as part of a circular economy approach to reducing the environmental impact of the concrete industry. However, it underlines the need to optimize formulations to maintain acceptable technical performance.
This study examines concrete polishing waste (CFPW) potential as a partial cement substitute in mortar formulation. Concrete polishing waste, a by-product of the grinding and polishing of concrete surfaces, is mainly composed of fine particles of silica and calcium carbonate. The aim of the research was to assess this industry waste incorporation impact on various mortar properties. Four mixes containing different percentages of CFPW were tested for their physic-mechanical properties and environmental impact. The results show that increasing the CFPW percentage leads to higher porosity and shrinkage, as well as lower mechanical strength and density. However, a significant reduction in CO2 emissions was observed with CFPW incorporation (up to 29% reduction for 30% CPFW). Although CFPW use presents technical challenges, it offers an interesting opportunity to reduce mortars’ carbon footprint. The study concludes that moderate CFPW use can offer a balance between environmental benefits and performance, highlighting the need to optimize formulations to maximize benefits while minimizing compromises on mechanical properties.
Portland cement production is energy- and carbon-intensive. Substituting part of the clinker with natural pozzolans is a promising route to lower-impact mortars. This work evaluates mortar where Portland cement is partially replaced by a German natural pozzolan (12–56% by mass). Compressive and flexural strengths were measured at 7, 28, and 90 d. Water-accessible porosity (28 d) and 24 h water absorption were also determined. Strength development and water transport were interpreted using (i) a three-parameter strength–age model and (ii) a capillary–diffusive model. The results showed delayed reactivity typical of pozzolanic materials. At 90 d, 12% replacement slightly exceeded the control by 3.38% and 1.4% in compressive and flexural strengths respectively. Higher replacement levels caused a drop in strength at 90 d (18.3% at 36% and 42.5% at 56% in compression; 25.3% and 31.0% in flexure). Porosity and absorption increased with replacement, consistent with the mechanical trends. The compressive and flexural strengths were strongly correlated. Life cycle analysis showed a significant reduction in embodied carbon, reaching approximately 52% at 56% replacement. Overall, moderate replacement (12–21%) provides the best balance between performance and carbon reduction.
In the field of prefabrication, the timely demolding of concrete elements is crucial to prevent structural failures during panel lifting. This study investigates the early-age compressive strength of different concrete mixtures by simulating various prefabrication plant scenarios. Special attention is given to winter conditions, where concrete hydration tends to be slower, potentially compromising the minimum compressive strength requirement of 10 MPa. The first scenario (reference), set at an ambient temperature of 20 °C with raw materials at room temperature, establishes the baseline for comparison. Two alternative dispositions are explored: Scenario 2, with an external temperature of 8 °C and the water for mixing at 35 °C, and Scenario 3, with the same external temperature but utilizing a heating hood to maintain the concrete at 35 °C. The experimental results shed light on the effectiveness of different strategies in achieving the desired early-age compressive strength under winter conditions. The use of warm mixing water and heating hoods are evaluated as potential measures to counteract the hydration slowdown. The findings contribute valuable insights for optimizing prefabrication processes in cold weather, ensuring the structural integrity of precast concrete elements.
The management of washing water from concrete plants is a growing environmental and industrial concern due to its high alkalinity and the presence of suspended solids, chemical admixtures, and dissolved salts. This study investigates the impact of collected and recycled concrete plant washing water on the physical, chemical, and mechanical properties of mortars. Two types of wastewater were analyzed: (1) collected water (CW), obtained from settling tanks with residual suspended particles and chemical compounds, and (2) recycled water (RW), subjected to a complete treatment process including pH stabilization and solid particle removal. The effects of these waters were compared against potable water (PW) through a comprehensive experimental program evaluating the porosity, density, shrinkage, and mechanical performance of mortars. The results indicate that using CW and RW leads to increased porosity, higher shrinkage, and a reduction in compressive and flexural strength, with RW having a more pronounced impact. These changes are attributed to the chemical composition of the water, which affects cement hydration and matrix densification. Despite these drawbacks, the proper treatment and controlled usage of such waters may offer sustainable alternatives to potable water in concrete production, contributing to resource conservation and environmental sustainability.