Retired batteries pose a significant current and future challenge for electric mobility due to their high cost and the need for a state of health (SOH) above 80% to supply energy efficiently. Recycling and alternative applications are the primary options for these batteries, with recycling still undergoing research as regards more efficient and cost-effective techniques. While advancements have been made, researchers are actively seeking improved methods. Repurposing retired batteries for lower-performance applications like stationary systems or low-speed vehicles is recommended. Second-life batteries (SLB) can be directly reused or reconstructed, with the latter involving the disassembly, measurement, and separation of cells based on their characteristics. The traditional measurement process, involving full charge and discharge cycles, is time-consuming. To address this, a Machine Learning (ML)-based SOH estimator is introduced in this work, offering the instant measurement and estimation of battery health without complete discharge. The results indicate that the model can accurately identify SOH within a nominal capacity range of 1400–2300 mAh, with a resolution near 45.70 mAh, in under five minutes of discharging. This innovative technique could be instrumental in selecting and assembling SLB packs.
This study presents the utilization of optical fiber Bragg gratings (FBGs) embedded into a carbon fiber reinforced polymer transtibial prosthesis to evaluate the user’s gait, as well as its own performance. Static mechanical tests were performed to characterize the sensors. Vertically and horizontally positioned FBGs within the structure have been used for load and strain force evaluation during real-time experiments with a candidate at different speeds on a treadmill. For simplicity, one non-amputee candidate performed the experiments using a mechanical adaptation. Distinctive patterns of response of the FBGs located at different points within the prosthetic structure enabled the differentiation between slow and fast motion gait cycle and the force distribution during the tread. This optical instrumentation contributes to the development of a new tool for the evaluation of prosthesis design and amputee patients rehabilitation and to the assessment of the performance of athletes during training or competition.
This paper presents a hybrid equalization (EQ) topology of lithium-ion batteries (LIB). Currently, LIBs are widely used for electric mobility due to their characteristics of high energy density and multiple recharge cycles. In an electric vehicle (EV), these batteries are connected in series and/or parallel until the engine reaches the voltage and energy capacity required. For LIBs to operate safely, a battery management system (BMS) is required. This system monitors and controls voltage, current, and temperature parameters. Among the various functions of a BMS, voltage equalization is of paramount importance for the safety and useful life of LIBs. There are two main voltage equalization techniques: passive and active. Passive equalization dissipates energy, and active equalization transfers energy between the LIBs. The passive has the advantage of being simple to implement; however, it has a longer equalization time and energy loss. Active is complex to implement but has fast equalization time and lower energy loss. This paper proposes the combination of these two techniques to implement simultaneously to control a pack of LIBs, equalizing voltage between stacks and at the cell level. For this purpose, a pack of LIBs was simulated with sixty-four cells connected in series and divided into eight stacks with eight battery cells each. The rated voltage of each cell is 3.7 V, with a capacity of 106 Ah. The total pack has a voltage of 236.8 V and 25 kW. Some LIBs were fitted with different SOC values to simulate an imbalance between cells. In the simulations, different topologies were evaluated: passive and active topology at the cell level and combined active and passive equalization at the pack level. Results are compared as a response time and state of charge (SOC) level. In addition, equalization topologies are applied in an EV model with the FTP75 conduction cycle. In this way, it is possible to evaluate the autonomy of each equalization technique simulated in this work. The hybrid topology active at the stack level and passive at the module level showed promising results in equalization time and autonomy compared with a purely active or passive equalization technique. This combination is a solution to achieve low EQ time and satisfactory SOC when compared to a strictly active or passive EQ.
This letter presents the utilization of optical fiber Bragg grating sensors for strain mapping of carbon fiber reinforced polymer below-knee prosthesis at different positions. Optical fiber sensors embedded within the prosthetic structure have a minimal impact on the design and enable real-time monitoring of the structure deformation. Tests were performed with a volunteer who is not amputated using a mechanical adaptor. The results obtained show the deformation of the mechanical structure of the prosthesis at different points, which can be helpful to record training sessions, detect material failures, or study ground reaction forces during periodic evaluations.
Lithium-ion batteries (LIBs) are the state-of-the-art technology for energy storage systems. LIBs can store energy for longer, with higher density and power capacity than other technologies. Despite that, they are sensitive to abuses and failures. If the battery management system (BMS) operates incorrectly or some anomalies appear, performance and security issues can be observed in LIBs. BMSs are also hard-programmed, have complex circuits, and have low computational resources, which limit the use of prognoses and diagnoses systems operating in real-time and embedded in the vehicle. Therefore, some technologies, such as edge and cloud computing, data-driven approaches, and machine learning (ML) models, can be applied to help the BMS manage the LIBs. Therefore, this work presents an edge–cloud computing system composed of two ML approaches (anomaly detection and failure classification) to identify the abuses in the LIBs in real-time. To validate the work, 36 NMC cells with a nominal capacity of 2200 mAh and voltage of 3.7 V were used to build the experiments segmented into three steps. Firstly, 12 experiments under failures were realized, which resulted in a high capacity loss. Then, the data were used to build both ML models. In the second step, the anomaly approach was applied to 12 cells observing the cells’ temperature anomalies. Then, the combination of IF and RF was applied to another 12 cells. The IF could reduce the capacity loss by about 45% when multiple abuses were applied to the cells. Despite that, this approach could not avoid some failures, such as overdischarging. Conversely, combining IF and RF could significantly reduce the capacity loss by 91% for the multiple abuses. The results concluded that ML could help the BMS identify failures in the first stage and reduce the capacity loss in LIBs.
This article presents two in vivo instrumentation techniques to study the different types of gait of horses performing athletics using fiber Bragg gratings (FBG). These techniques can be used as an auxiliary tool in the early diagnosis of injuries related to the horse’s locomotor system, mainly in the distal portion of the digit, one of the most common causes of retirement when they are athletes. Therefore, the first technique presented consists of the fixation of FBGs without encapsulation, directly on the dorsal wall of the hoof in each of the limbs. In the second technique presented, the FBG sensor is encapsulated in a prototype developed using a composite material reinforced with carbon fiber in a horseshoe shape. The second technique is associated with digital image processing (DIP) for better visualization of the deformation and compression forces that act upon the limbs. The first method showed sensitivity to detection of the digit compression against the ground, being able to identify walking patterns. The second technique, with the encapsulated sensor elements, also allows the capture of characteristic signals of gait, such as step walk, trot, and gallop under training conditions. Both, FBG sensor interrogation and DIP, analysis techniques have proven good performance and promising results for the clinical and biomechanical study and medical evaluations of horses even during dynamic training and competitions.