Giuseppe Battiato

Prof. Giuseppe Battiato


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 January 2018 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
Christian FirroneChristian Firrone
Christian Firrone
TBTeresa Maria Berruti
Teresa Maria Berruti
BEBogdan I. Epureanu
Bogdan I. Epureanu
Most aircraft turbojet engines consist of multiple stages coupled by means of bolted flange joints which potentially represent source of nonlinearities due to friction phenomena. Methods aimed at predicting the forced response of multistage bladed disks have to take into account such nonlinear behavior and its effect in damping blades vibration. In this paper, a novel reduced order model (ROM) is proposed for studying nonlinear vibration due to contacts in multistage bladed disks. The methodology exploits the shape of the single-stage normal modes at the interstage boundary being mathematically described by spatial Fourier coefficients. Most of the Fourier coefficients represent the dominant kinematics in terms of the well-known nodal diameters (standard harmonics), while the others, which are detectable at the interstage boundary, correspond to new spatial small wavelength phenomena named as extra harmonics. The number of Fourier coefficients describing the displacement field at the interstage boundary only depends on the specific engine order (EO) excitation acting on the multistage system. This reduced set of coefficients allows the reconstruction of the physical relative displacement field at the interface between stages and, under the hypothesis of the single harmonic balance method (SHBM), the evaluation of the contact forces by employing the classic Jenkins contact element. The methodology is here applied to a simple multistage bladed disk and its performance is tested using as a benchmark the Craig–Bampton ROMs of each single stage.

31 October 2017 in Journal of Computational and Nonlinear Dynamics
Verified
Journal Article
Closed access
PDF file
Christian FirroneChristian Firrone
Christian Firrone
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
BEBogdan I. Epureanu
Bogdan I. Epureanu
The complex architecture of aircraft engines requires demanding computational efforts when the dynamic coupling of their components has to be predicted. For this reason, numerically efficient reduced-order models (ROM) have been developed with the aim of performing modal analyses and forced response computations on complex multistage assemblies being computationally fast. In this paper, the flange joint connecting two turbine disks of a multistage assembly is studied as a source of nonlinearities due to friction damping occurring at the joint contact interface. An analytic contact model is proposed to calculate the local microslip based on the different deformations that the two flanges in contact take during vibration. The model is first introduced using a simple geometry representing two flanges in contact, and then, it is applied to a reduced finite element model in order to calculate the nonlinear forced response.

28 November 2022 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
VPValeria Pinto
Valeria Pinto
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
Christian FirroneChristian Firrone
Christian Firrone
The effect of differences in nominally equal sectors of a bladed disk (mistuning) is a well-known problem for designers since the forced response may show localized amplification of the blade response with respect to a cyclically symmetric (tuned) configuration. In order to perform a large number of simulations in a reasonable amount of time to characterize the highest blade response, corresponding to the worst mistuning pattern, reduction techniques have been developed, where the mistuning is introduced directly in a compact, reduced order model (ROM) obtained from very large finite element (FE) models. Typically, mistuning is introduced in the ROM in terms of natural frequency perturbations of the blade; nevertheless, a better insight is specifically required in order to correlate mistuning to a specific source (geometrical, material, contact mistuning). In this paper, a reduction technique is presented to take into account mistuning due to the contact uncertainties at the blade root joint, which can be caused by design tolerances, manufacturing process, assembly procedures, wear, etc. The technique takes its basis from the Craig–Bampton component mode synthesis (CB-CMS) applied to the uncoupled blade and disk sector, which is typically included in most of the FE software for easy implementation in standard industrial practice. The full set of master degrees-of-freedom (DOFs) at the random contacts are purposely reduced using an optimal local modal basis based on the Gram–Schmidt interface (GSI) technique developed by the authors. Experimental evidence of actual uncertain contact obtained during joint preloading is used to find an appropriate base to represent typical contact patterns.

15 September 2021 in Nonlinear Dynamics
Verified
Journal Article
Open access
PDF file
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
The steady-state nonlinear forced response (NFR) of finite element (FE) models with friction joints is usually computed in the frequency domain through the combination of node-to-node contact elements and the Harmonic Balance Method (HBM). In the current state of the art, rare are the cases where the friction forces are estimated for contact interfaces with non-conforming mesh grids. This need is nowadays taking place due to the improving capability of commercial FE software to manage any kind of boundary condition (i.e., either coupling or contact), without requiring coincident pairs of nodes at the joint interfaces. Such an advantage becomes a drawback when the analysts are requested to investigate the NFR of the assembly by using build-in codes, where the contact forces prediction usually requires node-to-node contact elements whose parameters (i.e., the contact stiffnesses and friction coefficients) can be easily identified by means of experiments. This paper addresses the mentioned limitation, and proposes a novelself-adaptive macroslip array(SAMA) model for the estimation of the nonlinear friction forces on FE contact interfaces with non-conforming meshes. The SAMA model consists on a set of node-to-node contact elements ordered in parallel, whose contact parameters and normal preloads are identified through a step-by-stepself-adaptiveweighting algorithm that depends on the topology of the meshes in contact. The goodness of the proposed model is assessed on the calculation of the NFR of a bladed disk with shroud contacts, under the hypotheses of cyclic symmetry and HBM. The nonlinear dynamic behavior of the bladed disk is evaluated in two different cases. First, in the case of lack of node-to-node congruence at the contact interface for the structure being in its undeformed configuration, and second, in the case of a relevant static misalignment of the contact interfaces due to the application of large static loads.

17 June 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YWYongfeng Wang
Yongfeng Wang
YMYanhong Ma
Yanhong Ma
JHJie Hong
Jie Hong
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
Christian FirroneChristian Firrone
Christian Firrone
The paper aims at performing a comprehensive experimental study on the peculiar properties of a bolted joint, and investigates the damping induced at different interfaces (between flanges, bolt head/nut and flange, threads) during vibrations. A novel, simplified, single-bolt system joining a two-beam structure is designed and tested. Experimental results under different boundary conditions are presented, and the influence of the harmonic excitation force, as well as the bolt tension, is investigated. The test results show how the contact interface between the clamped flanges plays an important role in terms of frictional damping provided to the system during vibration, while the contact interfaces between the head/nut and flange, and secondarily between the threads, affect the system response at a less, but not negligible, extent. The test setup and test procedure can provide a database to validate single bolt contact models to be included in a more complex structure.

19 September 2024 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
BZBiao Zhou
Biao Zhou
CXChengyu Xie
Chengyu Xie
Giuseppe BattiatoGiuseppe Battiato
Giuseppe Battiato
TBTeresa Maria Berruti
Teresa Maria Berruti
This paper explores two different blisk dynamic models for resonant vibration prediction of a rotating blisk test piece, i.e., the Model-BDTID and geometrically mistuned models (GMM). The former represents a mistuned blisk model with blade mistuning pattern experimentally retrieved by a recently proposed blade mistuning identification method based on blade detuning tests (BDTID). It falls into the scope of the frequency-mistuning modeling approach. The latter refers to a geometrically mistuned model constructed upon high-precision blisk geometry data by leveraging the advanced optical geometry measurement technology. A specifically developed “Sector Mode Assembling Reduction Technique” is exploited for efficient dynamic analyses of the large-sized GMM. Forced response tests are performed in a spinning rig under well-controlled laboratory condition. The blade tip-timing (BTT) technique is employed to give all-blade vibration measurements of the rotating blisk. Correlation results between the forced response predictions to BTT measurements demonstrate that both the Model-BDTID constructed upon the identified blade mistuning of the blisk at rest and the GMM, can predict the resonant vibration of the rotating blisk with satisfactory accuracy.