Grzegorz Bogusławski

Dr. Grzegorz Bogusławski

Lodz University of Technology

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2005 in Surface and Coatings Technology
Verified
Journal Article
Closed access
ASA. Sokołowska
A. Sokołowska
JRJ. Rudnicki
J. Rudnicki
PNPiotr Niedzielski
Piotr Niedzielski
Anna BoczkowskaAnna Boczkowska
Anna Boczkowska
GBGrzegorz Bogusławski
Grzegorz Bogusławski
Stanislaw MituraStanislaw Mitura
Stanislaw Mitura

6 July 2023 in Combustion Engines
Verified
Journal Article
Open access
LSLukasz Stajuda
Lukasz Stajuda
DLDmytro Levchenko
Dmytro Levchenko
PKPrzemyslaw Kubiak
Przemyslaw Kubiak
KSKamil Siczek
Kamil Siczek
GBGrzegorz Bogusławski
Grzegorz Bogusławski
KSKrzysztof Siczek
Krzysztof Siczek
Vehicle coolant is one of the most important operating fluids. Along with changes in the design of engines, the composition of the coolant has also changed. The main function of the coolant is heat transfer (HT). It absorbs up to one-third of the heat energy generated by the engine. The coolant is also responsible for protecting the cooling system from damage caused by corrosion, scaling and deposits. The unfavorable working environment of the engine is also affected by smaller capacities of the cooling systems (CSs) of the drive units, extreme temperatures and increased pressure in the CS, enhancing the importance of the fluid composition. The coolant must be replaced every three years or 100,000 kilometers or every five years or 250,000 kilometers with the Organic Acid Technology (OAT). It is worth remembering that coolant of unknown composition or low quality used for a long time can expose the system to engine overheating, corrosion, deposits and restriction of liquid flow. This can lead to engine failure, in extreme cases even engine seizure. Currently, there are many types of fluids, including nanocoolants with different compositions, that are available on the cooling market. The article presents these fluids, describe the most common failures of CSs, present the currently used methods of fluid replacement in the engine and proposes an innovative method based on the pressure method, which allows both replacing the fluid in the entire system and cleaning it.

1 October 2020 in Energies
Verified
Journal Article
Open access
PDF file
KSKrystian Siczek
Krystian Siczek
KSKrzysztof Siczek
Krzysztof Siczek
PPPiotr Piersa
Piotr Piersa
ŁAŁukasz Adrian
Łukasz Adrian
Szymon SzufaSzymon Szufa
Szymon Szufa
GBGrzegorz Bogusławski
Grzegorz Bogusławski
The stationary photovoltaic array can be used to charge the different vehicle batteries and, in parallel, be used as a power source for the utility grid or standalone devices placed such as in campers. The main objective of the study was to compare chosen electrical characteristics of two assemblies with each containing the same PV array, boost converter and inverter, and a different battery, such as the Li-S one and the Li-ion one, respectively. Differences occurring during modelling of Li-ion and Li-S batteries were discussed. The model of the chosen photovoltaic array was used during analysis. The models based on electrical equivalent circuits for Li-ion battery and of Li-S battery were utilized during calculations. The models of the boost converter and boost inverter of known topology parameters were utilized during simulations. In the chosen performances (courses of voltages and currents versus time) obtained from the simulation of the sets composed of the Li-S battery cooperating with the boost inverter or the boost converter, only small differences or no differences occurred when compared to the case of the Li-ion battery.

5 June 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Joanna Maria KopaniaJoanna Maria Kopania
Joanna Maria Kopania
WZWojciech Zakrzewicz
Wojciech Zakrzewicz
Przemyslaw KubiakPrzemyslaw Kubiak
Przemyslaw Kubiak
AMAdam Mrowicki
Adam Mrowicki
MGMichał Głogowski
Michał Głogowski
PGPatryk Gaj
Patryk Gaj
The primary goal of this research was to study transmission loss and absorption of fluted PVC panels using experimental and theoretical methods. During these studies, the link between panel size, thickness, transmission loss, and absorption was considered. We measured the transmission loss and absorption in reverberation rooms according to ISO standards. Hansen’s theoretical model was also used to predict the transmission loss. Agreement between TL prediction according to Hansen’s model and measured results for some of the studied panels were observed. However, the analytical prediction, according to Hansen’s model, for heavy fluted PVC panels must be used with caution. The absorption properties of the studied fluted PVC panels are also connected with their resonance, and, in addition, the resonance frequency is associated with the space between the ribs and wave propagation in the panel’s plane.

1 November 2015 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
GBGrzegorz Bogusławski
Grzegorz Bogusławski
This paper is aimed at developing the system assisting an orthotics specialist during correction process of orthoses structure. Orthotics is a specialty within medical field increasingly progressing in terms of variety of offered services, equipment and materials used. Further mentioned in this paper is the usage of optical scanning, depending on making series of photos in split second and then assembling then into 3D model, thus eliminating drawbacks of the classical methods based on the plaster cast preparation. The objective of such computer aided design is evaluation of the influence of prostheses shape modifications on their features.