Xiaowei Guo

Dr. Xiaowei Guo

China University of Mining and Technology, Xuzhou, China
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
NSNiaz Muhammad Shahani
Niaz Muhammad Shahani
Muhammad KamranMuhammad Kamran
Muhammad Kamran
XZXigui Zheng
Xigui Zheng
CLCancan Liu
Cancan Liu
Xiaowei GuoXiaowei Guo
Xiaowei Guo
The uniaxial compressive strength (UCS) of rock is one of the essential data in engineering planning and design. Correctly testing UCS of rock to ensure its accuracy and authenticity is a prerequisite for assuring the design of any rock engineering project. UCS of rock has a broad range of applications in mining, geotechnical, petroleum, geomechanics, and other fields of engineering. The application of the gradient boosting machine learning algorithms has been rarely used, especially for UCS prediction, and has performed well, based on the relevant literature of the study. In this study, four gradient boosting machine learning algorithms, namely, gradient boosted regression (GBR), Catboost, light gradient boosting machine (LightGBM), and extreme gradient boosting (XGBoost), were developed to predict the UCS in MPa of soft sedimentary rocks of the Block‐IX at Thar Coalfield, Pakistan, using four input variables such as wet density (ρw) in g/cm3; moisture in %; dry density (ρd) in g/cm3; and Brazilian tensile strength (BTS) in MPa. Then, 106‐point dataset was allocated identically for each algorithm into 70% for the training phase and 30% for the testing phase. According to the results, the XGBoost algorithm outperformed the GBR, Catboost, and LightGBM with coefficient of correlation (R2) = 0.99, mean absolute error (MAE) = 0.00062, mean square error (MSE) = 0.0000006, and root mean square error (RMSE) = 0.00079 in the training phase and R2 = 0.99, MAE = 0.00054, MSE = 0.0000005, and RMSE = 0.00069 in the testing phase. The sensitivity analysis showed that BTS and ρw are positively correlated, and the moisture and ρd are negatively correlated with the UCS. Therefore, in this study, the XGBoost algorithm was shown to be the most accurate algorithm among all the investigated four algorithms for UCS prediction of soft sedimentary rocks of the Block‐IX at Thar Coalfield, Pakistan.

21 March 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
NSNiaz Muhammad Shahani
Niaz Muhammad Shahani
Xigui ZhengXigui Zheng
Xigui Zheng
Xiaowei GuoXiaowei Guo
Xiaowei Guo
XWXin Wei
Xin Wei
Elastic modulus (E) is a key parameter in predicting the ability of a material to withstand pressure and plays a critical role in the design of rock engineering projects. E has broad applications in the stability of structures in mining, petroleum, geotechnical engineering, etc. E can be determined directly by conducting laboratory tests, which are time consuming, and require high-quality core samples and costly modern instruments. Thus, devising an indirect estimation method of E has promising prospects. In this study, six novel machine learning (ML)-based intelligent regression models, namely, light gradient boosting machine (LightGBM), support vector machine (SVM), Catboost, gradient boosted tree regressor (GBRT), random forest (RF), and extreme gradient boosting (XGBoost), were developed to predict the impacts of four input parameters, namely, wet density (ρwet) in gm/cm3, moisture (%), dry density (ρd) in gm/cm3, and Brazilian tensile strength (BTS) in MPa on output E (GPa). The associated strengths of every input and output were systematically measured employing a series of fundamental statistical investigation tools to categorize the most dominant and important input parameters. The actual dataset of E was split as 70% for the training and 30% for the testing for each model. In order to enhance the performance of each developed model, an iterative 5-fold cross-validation method was used. Therefore, based on the results of the study, the XGBoost model outperformed the other developed models with a higher accuracy, coefficient of determination (R2 = 0.999), mean absolute error (MAE = 0.0015), mean square error (MSE = 0.0008), root mean square error (RMSE = 0.0089), and a20-index = 0.996 of the test data. In addition, GBRT and RF have also shown high accuracy in predicting E with R2 values of 0.988 and 0.989, respectively, but they can be used conditionally. Based on sensitivity analysis, all parameters were positively correlated, while BTS was the most influential parameter in predicting E. Using an ML-based intelligent approach, this study was able to provide alternative elucidations for predicting E with appropriate accuracy and run time at Thar coalfield, Pakistan.

17 September 2019 in Journal of Ambient Intelligence and Humanized Computing
Verified
Journal Article
Closed access
PDF file
Jun ZhaoJun Zhao
Jun Zhao
JWJiaji Wu
Jiaji Wu
Xiaowei GuoXiaowei Guo
Xiaowei Guo
JHJie Han
Jie Han
KYKai Yang
Kai Yang
HWHongguang Wang
Hongguang Wang

9 November 2021 in Energies
Verified
Journal Article
Open access
PDF file
Xiaowei GuoXiaowei Guo
Xiaowei Guo
Xigui ZhengXigui Zheng
Xigui Zheng
PLPeng Li
Peng Li
RLRui Lian
Rui Lian
CLCancan Liu
Cancan Liu
GLGuowei Lai
Guowei Lai
The traditional anchoring method of bolts has insufficient control over the surrounding rock of the coal roadway. Based on this background, full-stress anchoring technology of bolts was proposed. Firstly, a mechanical relationship model of a bolt-drawing, anchoring interface was established to obtain the equations of the axial force and obtain shear stress distribution as well as the decreasing-load transfer law of the anchoring section of bolts. Through studying the prestress-loading experimental device of bolts, we found that increasing the initial preload could increase the axial force under the same conditions and the retarded anchoring section could control the axial-force loss of bolts in the middle of the anchoring section. Under the full-stress anchoring mode, the effect of applying a pre-tightening force was better than that of applying a pre-tightening force under traditional anchoring methods. Moreover, FLAC3D (Fast Lagrangian Analysis of Continua 3D; ITASCA (Ita sca International Inc), Minnesota, USA) numerical simulation calculation was performed. Under the full-stress anchoring mode of bolts, the increased anchoring length reduced the damage of the anchoring section, with a wider control range of the rock formation and higher strength of the compressive-stress anchoring zone. Based on the above research, four methods for applying the full-stress anchoring technology of bolts in engineering were proposed. The full-stress anchoring technology of bolts in the coal roadway has been applied in the support project of the return-air roadway at working face 3204 of the Taitou Coking Coal Mine of the Xiangning Coking Coal Group, Shanxi. The maximum moving distance of the roof and floor of the roadway was reduced from 200 to 42 mm, and the maximum moving distance on both coal sides was reduced from 330 to 86 mm. The full-stress anchoring technology of bolts was able to control the surrounding rock in the coal roadway.

20 July 2021 in PLOS ONE
Verified
Journal Article
Open access
PDF file
CLCancan Liu
Cancan Liu
XZXigui Zheng
Xigui Zheng
NSNiaz Muhammad Shahani
Niaz Muhammad Shahani
PLPeng Li
Peng Li
CWCong Wang
Cong Wang
Xiaowei GuoXiaowei Guo
Xiaowei Guo
Measurement while drilling is an important part of the intelligent development of coal mines. The main purpose of this paper is to comprehensively analyze the response characteristics of borehole drilling parameters and find a better method to predict rock mechanical properties based on drilling parameters. Firstly, six concrete blocks and multiple specimens were prepared with different material ratios. Next, the concrete specimens were tested for mechanical properties in the laboratory. Meanwhile, the displacement, rotation speed, torque, and sound pressure level (SPL) were observed during the drilling of the concrete blocks. Finally, the response characteristics of drilling parameters such as rotation speed, rate of penetration (ROP), torque, and SPL were analyzed. Besides, multiple prediction models of rock mechanical parameters were obtained by data analysis. The research results indicate that the drilling process can be classified into the initial stage of drilling (fast speed) and the steady stage of drilling (slow speed). The torque work ratio accounts for more than 99%, which increases with the increase in rock strength. The penetration depth per revolution and torque work ratio are significantly related to rock uniaxial compressive strength, Brazilian tensile strength, cohesion, and elastic modulus. The ROP is the best choice for estimating rock mechanical parameters. This research provides an important reference for laboratory rock mechanics parameter testing and geological features detection based on drilling parameters.

26 March 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
CLCancan Liu
Cancan Liu
XZXigui Zheng
Xigui Zheng
LYLu Yang
Lu Yang
PLPeng Li
Peng Li
NSNiaz Muhammad Shahani
Niaz Muhammad Shahani
Xiaowei GuoXiaowei Guo
Xiaowei Guo
Borehole imaging, one of the main methods of rock formation detection, is widely used in mining, tunnels, petroleum, and other fields of engineering. However, the method of manually identifying the characteristic of rock formation based on borehole imaging is greatly affected by subjective factors. For example, it should be noted that when the rock layer color is similar, the position of the rock interface may be different. In this paper, a method of quantitatively describing the characteristics of the rock formation is proposed, and the automatic recognition of the rock interface is realized. Firstly, the calculation method of rock dip angle and position based on borehole image with 360° wall surface development is proposed. Secondly, the three-dimensional distribution characteristics of the gray values of the rock layer are used to quantitatively describe the characteristics of the rock layer. Finally, an automatic recognition method of rock formation interface based on change-point detection algorithm is proposed. In addition, the recognition effect of the rock formation interface is analyzed by experiments and applied in the field. Research shows that, compared with method two, method one can determine the rock inclination. But its anti-interference ability is poor. Method two can better determine the position of the rock interface. The method is of great significance to the intelligent development of the borehole imaging system and promotes safe, efficient, and sustainable mining in coal mines.