This paper presents a method of determining electromotive force and battery internal resistance as time functions, which are depicted as functions of state of charge (SOC) because . The model is based on battery discharge and charge characteristics under different constant currents that are tested by a laboratory experiment. This paper further presents the method of determining the battery SOC according to a battery modeling result. The influence of temperature on battery performance is analyzed according to laboratory-tested data, and the theoretical background for calculating the SOC is obtained. The algorithm of battery SOC indication is depicted in detail. The algorithm of the battery SOC ldquoonlinerdquo indication considering the influence of temperature can be easily used in practice by a microprocessor. An NiMH battery is used in this paper to depict the modeling method. In fact, the method can also be used for different types of contemporary batteries, as well as Li-ion batteries, if the required test data are available.
Hybrid power systems, formed by combining high-energy-density batteries and high-power-density ultracapacitors in appropriate ways, provide high-performance and high-efficiency power systems for electric vehicle applications. This paper first establishes dynamic models for the ultracapacitor, the battery and a passive hybrid power system, and then based on the dynamic models a comparative simulation between a battery only power system and the proposed hybrid power system was done under the UDDS (Urban Dynamometer Driving Schedule). The simulation results showed that the hybrid power system could greatly optimize and improve the efficiency of the batteries and their dynamic current was also decreased due to the participation of the ultracapacitors, which would have a good influence on batteries’ cycle life. Finally, the parameter matching for the passive hybrid power system was studied by simulation and comparisons.
This paper deals with the speed synchronization controller design for networked integrated motor-transmission (IMT) powertrains via controller area network (CAN). It is well known that, in current implementations, CAN has been widely used in the control system design of automotive powertrains. However, on the other hand, the application of CAN would not only lead to network-induced delays but also bring about protocol constrains, e.g., data package capability and utilization ratio limitation, which would deteriorate the system and make the controller design a challenging problem. This paper is to provide a co-design methodology that can cope with all these problems and ensure satisfactory control effect for the speed synchronization control of IMT powertrain systems. First, a networked IMT powertrain system using CAN as underlying network is presented and the dynamic model for the speed synchronization control is derived. Second, the network-induced delay model is introduced and improved considering data packet capability and utilization ratio limitation. The control-orient discrete-time model is also derived based on the improved delay model. Third, a co-design methodology using sliding mode controller and offline priority scheduling based on Lyapunov stability criterion is proposed. The results of simulations and tests show the effectiveness of the proposed co-design methodology.
22 January 2017 in Mathematical Problems in Engineering
This paper investigates the robust direct yaw‐moment control (DYC) through parameter‐dependent fuzzy sliding mode control (SMC) approach for all‐wheel‐independent‐drive electric vehicles (AWID‐EVs) subject to network‐induced delays. AWID‐EVs have obvious advantages in terms of DYC over the traditional centralized‐drive vehicles. However it is one of the most principal issues for AWID‐EVs to ensure the robustness of DYC. Furthermore, the network‐induced delays would also reduce control performance of DYC and even deteriorate the EV system. To ensure robustness of DYC and deal with network‐induced delays, a parameter‐dependent fuzzy sliding mode control (FSMC) method based on the real‐time information of vehicle states and delays is proposed in this paper. The results of cosimulations with Simulink® and CarSim® demonstrate the effectiveness of the proposed controller. Moreover, the results of comparison with a conventional FSMC controller illustrate the strength of explicitly dealing with network‐induced delays.
All-wheel-independent-drive electric vehicles (AWID-EVs) have considerable advantages in terms of energy optimization, drivability and driving safety due to the remarkable actuation flexibility of electric motors. However, in their current implementations, various real-time data in the vehicle control system are exchanged via a controller area network (CAN), which causes network congestion and network-induced delays. These problems could lead to systemic instability and make the system integration difficult. The goal of this paper is to provide a design methodology that can cope with all these challenges for the lateral motion control of AWID-EVs. Firstly, a continuous-time model of an AWID-EV is derived. Then an expression for determining upper and lower bounds on the delays caused by CAN is presented and with which a discrete-time model of the closed-loop CAN system is derived. An expression on the bandwidth utilization is introduced as well. Thirdly, a co-design based scheme combining a period-dependent linear quadratic regulator (LQR) and a dynamic period scheduler is designed for the resulting model and the stability criterion is also derived. The results of simulations and hard-in-loop (HIL) experiments show that the proposed methodology can effectively guarantee the stability of the vehicle lateral motion control while obviously declining the network congestion.