Battery research depends upon up-to-date information on the cell characteristics found in current electric vehicles, which is exacerbated by the deployment of novel formats and architectures. This necessitates open access to cell characterization data. Therefore, this study examines the architecture and performance of first-generation Tesla 4680 cells in detail, both by electrical characterization and thermal investigations at cell-level and by disassembling one cell down to the material level including a three-electrode analysis. The cell teardown reveals the complex cell architecture with electrode disks of hexagonal symmetry as well as an electrode winding consisting of a double-sided and homogeneously coated cathode and anode, two separators and no mandrel. A solvent-free anode fabrication and coating process can be derived. Energy-dispersive X-ray spectroscopy as well as differential voltage, incremental capacity and three-electrode analysis confirm a NMC811 cathode and a pure graphite anode without silicon. On cell-level, energy densities of 622.4 Wh/L and 232.5 Wh/kg were determined while characteristic state-of-charge dependencies regarding resistance and impedance behavior are revealed using hybrid pulse power characterization and electrochemical impedance spectroscopy. A comparatively high surface temperature of ∼70 °C is observed when charging at 2C without active cooling. All measurement data of this characterization study are provided as open source.
In order to make electric transportation more accessible, the cost of lithium‐ion batteries must decrease. One way to achieve this is by increasing the production rates, especially in the time‐consuming steps of electrolyte filling and cell formation. Within this work, lithium‐ion pouch and hardcase cells are filled with electrolyte and the formation is started at varying wetting degrees. Data from the formation, stabilization, and life cycle testing are analyzed to determine the effect of an incomplete wetting degree on the cell quality. Additionally, postmortem analysis is performed to help understand the mechanisms induced when a cell with incomplete wetting is subjected to a current. The pouch cells demonstrate a linear capacity fade, regardless of the wetting degree, but feature strong lithium plating which becomes visible during postmortem analysis. In contrast, the hardcase cells display a clear correlation between the cell quality and the wetting degree in both the life cycle test and the postmortem analysis. It is shown that a wetting degree of 98% is required before starting the formation to avoid lithium plating in the cell.
In order to meet consumer demands for electric transportation, the energy density of lithium-ion batteries (LIB) must be improved. Therefore, a trend to increase the overall size of the individual cell and to decrease the share of inactive materials is needed. The process of electrolyte filling involves the injection of electrolyte liquid into the cell, as well as the absorption of the electrolyte into the pores of the electrodes and the separator, which is known as wetting. The trend towards larger-format LIB challenges the electrolyte filling due to an increase in wetting distance for the electrolyte as well as a decrease in the void volume of the cell. The optimization of the process via numerical simulation promises to reduce costs and ensure quality during battery production. The two models developed in this study are based on a commercial computational fluid dynamics (CFD) program to study the effect of process parameters, such as pressure and temperature, on the filling process. The results were verified with neutron radiography images of the dosing process and a feasibility study for a wetting simulation is shown. For all simulations, specific recommendations are provided to set up the electrolyte filling process, based on which factors generate the greatest improvement.
The electrolyte filling process is considered one of the bottlenecks of lithium‐ion battery production due mainly to the long electrolyte wetting times. Additionally, the required experimental process design is time and material‐intensive, increasing the development costs of new materials or cell designs. A model of the filling process would allow for more efficient cell production, but until now, the published models have mainly been focused on individual components on a pore scale. Within the scope of this work, the model setup for a holistic examination of the electrolyte filling process is shown, allowing the study of the electrolyte wetting on a cell scale. The characteristic values of a porous medium, such as the permeability, are calculated with a microsimulation of an anode and a cathode pore structure. These values are then transferred to the ANSYS porous media model, and cell scale simulations are performed. Two cell formats and variations in the evacuation pressure and electrolyte temperature are simulated and compared to experimental wetting data. The results show that the simulation successfully models the wetting behavior for the investigated cell formats and cell assembly types, validating the model with experimental data both qualitatively and quantitatively.