The automotive industry is one of the fastest-growing sectors of the modern economy. Growing customer expectations, implementing solutions related to electromobility, and increasingly stringent legal restrictions in the field of environmental protection, determine the development and introduction of innovative technologies in the field of car production. To power the most modern vehicles that include electric and hybrid cars, packages of various types of lithium-ion cells are used, the number of which is constantly growing. After use, these batteries, due to their complex chemical composition, constitute hazardous waste that is difficult to manage and must be recycled in modern technological lines. The article presents the morphological characteristics of the currently used types of Li-ion cells, and the threats to the safety of people and the environment that may occur in the event of improper use of Li-ion batteries and accumulators have been identified and described on the basis of the Regulation of the European Parliament and Council (EC) No. 1272/2008 of 16 December 2008 and No. 1907/2006 of 18 December 2006 on the classification, labeling and packaging of substances and mixtures and the registration, evaluation, authorization and restriction of chemicals (REACH), establishing the European Chemicals Agency.
Presently, most passive safety tests are performed with a precisely specified seat position and carefully seated ATD (anthropomorphic test device) dummies. Facing the development of autonomous vehicles, as well as the need for safety verification during crashes with various seat positions such research is even more urgently needed. Apart from the numerical environment, the existing testing equipment is not validated to perform such an investigation. For example, ATDs are not validated for nonstandard seatback positions, and the most accurate method of such research is volunteer tests. The study presented here was performed on a sled test rig utilizing a 50cc Hybrid III dummy according to a full factorial experiment. In addition, input factors were selected in order to verify a safe test condition for surrogate testing. The measured value was head acceleration, which was used for calculation of a head injury criterion. What was found was an optimal seat angle −117°—at which the head injury criteria had the lowest represented value. Moreover, preliminary body dynamics showed a danger of whiplash occurrence for occupants in a fully-reclined seat.
Accelerating process of the transport and energy sectors increases the interest in fuels derived from renewable sources. The predicted three-fold increase in hydrogen production by 2050, driven by its falling production costs, justifies the direction of research aimed at its popularisation as a fuel for internal combustion engines (H2ICE). Presented article provides an overview of the state of knowledge on hydrogen combustion systems, which are currently the most attractive development path, mainly due to the well-developed production technology and relatively low recycling cost compared with fuel cells. The paper contains a comprehensive analysis of currently available solutions covering issues related to the production, storage, and transmission of hydrogen, with particular emphasis on the Polish market, which is one of the largest in Europe in terms of its production. The authors also propose their own concept of a hydrogen combustion system for application in an internal combustion engine. The presented solution is based on the idea of prechamber introduction in order to improve combustion process parameters and hence overall engine efficiency.
The use of hydrogen as a fuel for an internal combustion engines has caused many problems for years, the most significant of which seems to be the excessive emission of nitrogen oxides and the tendency to knock combustion. In order to ensure better control of the combustion process in a internal combustion engine powered by hydrogen, it has been proposed to use a split combustion chamber solution. Following paper contains a description of a hydrogen combustion system that includes an analysis of possible technical solutions. The considerations take into account the issues of the dual nature of hydrogen knocking and the problem of burning a stratified charge of a hydrogen-air mixture in a cylinder.
Relatively large results discrepancies observed in vehicles emission tests became a reason for change of test procedure. The New European Driving Cycle (NEDC) test was replaced by more dynamic Worldwide Harmonized Light Vehicles Test Procedure (WLTP) on September 2017, however it occurred that emissions obtained in WLTP are still far from real ones. Due to that fact a new Real Driving Emissions (RDE) test was introduced in order to complement WLTP. RDE testing involves emissions measurement while vehicle being driven in real traffic conditions which is the biggest difference from previous tests conducted on chassis dynamometer. Because of that it is suspected that repeatability of RDE tests is significantly lower than in case of WLTP or even does not have to appear. Subject of authors investigation was evaluation of RDE tests repeatability. It included portable emission measuring system (PEMS) installation on vehicle and six test runs along test route designed in accordance with European Commission requirements. Results were then compared regarding to velocity profile of vehicle. Performed analysis involved statistical distribution of velocity profiles and their kurtosis and skewness comparison. It was found that tests repeatability occurs for some velocity ranges, however it is not satisfactory. Conclusions present the concept of further research on this problem.