In this work, a numerical model has been applied in order to obtain the wall pressure fluctuations at the volute of an industrial centrifugal fan. The numerical results have been compared to experimental results obtained in the same machine. A three-dimensional numerical simulation of the complete unsteady flow on the whole impeller-volute configuration has been carried out using the computational fluid dynamics code FLUENT®. This code has been employed to calculate the time-dependent pressure both in the impeller and in the volute. In this way, the pressure fluctuations in some locations over the volute wall have been obtained. The power spectra of these fluctuations have been obtained, showing an important peak at the blade passing frequency. The amplitude of this peak presents the highest values near the volute tongue, but the spatial pattern over the volute extension is different depending on the operating conditions. A good agreement has been found between the numerical and the experimental results.
Centrifugal fans are widely used in several applications, and in some cases, the noise generated by these machines has become a serious problem. The centrifugal fan noise is frequently dominated by tones at the blade passing frequency as a consequence of the strong interaction between the flow discharged from the impeller and the volute tongue. In this study, a previously published aeroacoustic prediction methodology (Cho, Y., and Moon, Y.J., 2003, “Discrete Noise Prediction of Variable Pitch Cross-Flow Fans by Unsteady Navier-Stokes Computations ,” ASME J. Fluids Eng., 125, pp. 543–550) has been extended to three-dimensional turbulent flow in order to predict the noise generated by a centrifugal fan. A three-dimensional numerical simulation of the complete unsteady flow on the whole impeller-volute configuration has been carried out using the computational fluid dynamics code FLUENT ® . The unsteady forces applied by the fan blades to the fluid are obtained from the data provided by the simulation. The Ffowcs Williams and Hawkings model extension of Lighthill’s analogy has been used to predict the aerodynamic noise generated by the centrifugal fan from these unsteady forces. Also, the noise generated by the fan has been measured experimentally, and the experimental results have been compared to the numerical results in order to validate the aerodynamic noise prediction methodology. Reasonable agreement has been found between the numerical and the experimental results.
The connection between an intake fan and a ventilation shaft must be designed in such a way that it minimizes the energy waste due to singularity losses. As a result, the questions of which radius of curvature to use and if guide vanes have to be included need to be answered. In that case, the variables such as the number, upstream and downstream penetration length, radius of curvature, and width of the vanes, need to be defined. Although this work is oriented to mine ventilation, these questions are usually valid in other engineering applications as well. The objective of this study is to define the previously mentioned variables to determine the optimal design combination for the radius/diameter relationship (r/D). Computational fluid dynamics was used to determine the shock loss factor of seven elbow curvature ratios for a 3 m diameter duct and fan, with and without guide vanes to estimate the best performing configuration and, therefore, to maximize the fan airflow volume. The methodology used consisted of initially developing models in 2D geometries, to optimize the meshing and the CPU use, and studying separately the number of vanes, upstream and downstream penetration, radius of curvature, and width of the vanes for each curvature ratio (r/D). Then, the best-performing variable combinations for each curvature ratio were selected to be simulated and studied with the 3D geometries. The application of the guide vane designs for three-dimensional simulated geometries is presented, first without and then with guide vanes, including the shock loss factors obtained. The methodology and obtained results allowed quantifying the energy savings and to reduce the CFD simulations steps required to optimize the design of the elbow and guide vanes. The results obtained cannot be used with elbows in exhaust fans, because fluid dynamics phenomena are different.
The evolution toward sustainable mining can be achieved by implementing circular economies (CEs), and one way forward is via product-service systems (PSSs). However, applying PSSs in the mining industry is an area with little extant research. We seek to contribute to CE and sustainability research by proposing a model by which mining companies can achieve circularity through their suppliers: something which has not yet been explored. First, we present a critical literature review of published papers about the barriers and benefits in industries where servitization or PSS has been applied. We discuss barriers impeding PSS implementation in the mining industry, along with related concepts including CE and PSSs in digital technologies. With this study we hope to draw more discussion to the topic of PSSs in the mining industry and provide useful guidelines to academics and industry professionals for PSS implementation in mining: an important step toward circularity.